(5)
 Adjust the clearance between the rollers and the guide fittings (Ref. TASK 52-11-00-820-001).

 Subtask 52-13-31-420-055
 D. Installation of the Roller
 (Ref. Fig. 405/TASK 52-13-31-991-007)

 (1)
 Clean the contact surface between the fitting and the structure with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003) if necessary.

 (2)
 Apply a layer of SEALANTS (Material No. 09-005) on the contact surface between the fitting and the structure.

 1EFF : ALL 1 52-13-31Page 429 1 1 Aug 01/98R 1 1 1CES 1

 (3)
 Put the fitting (60) in position.

 (4)
 Install the bolts (62).

 (5)
 Install the nuts (61) and tighten them.

 (6)
 Install the roller as follows:

 (a)
 Install the bushing (77).

 (b)
 Put the roller (70) in position.

 (c)
 Install the bushing (76), the washer (73) and the bolt (74).

 (d)
 Install the nut (72) and tighten it.

 (e) Install a new cotter pin (71). Subtask 52-13-31-420-056
 E. Installation of the Door Stop Fittings
 (Ref. Fig. 406/TASK 52-13-31-991-008)

 (1)
 Clean the contact surface between the door and the stop fittings with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003) if necessary.

 (2)
 Apply a layer of SEALANTS (Material No. 09-005) on the contact surface between the fittings and the structure.

 (3)
 Put the fitting (85) in position.

 (4)
 Install the bolts (84).

 (5)
 Install the nuts (81) and tighten them.

 (6)
 Install the screw (86).

 (7)
 Install a new lock plate (83).

 (8)
 Install the nut (82).

 (9)
 Adjust the stop screw (86) to get a correct clearance in the Y axis (Ref. TASK 52-11-00-820-001).

 (10) TORQUE the nut (52) to between 2 and 2.2 m.daN (14.74 and 16.22 lbf.ft).
 1EFF : ALL 1 52-13-31Page 430 1 1 Aug 01/98R 1 1 1CES 1

 (11) Safety the nut with the lock plate (83). Subtask 52-13-31-420-057
 F. Installation of the Roller Fitting
 (Ref. Fig. 407/TASK 52-13-31-991-009)

 (1)
 Clean all the components with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003) if necessary.

 (2)
 Apply a layer of SEALANTS (Material No. 09-005) on the contact surfaces between the fitting and the structure.

 (3)
 Put the fitting (90) in position.

 (4)
 Install the bolts (92).

 (5)
 Install the nuts (91) and tighten them.

 (6)
 Install the spacer (98) and the roller (97).

 (7)
 Apply a layer of SPECIAL MATERIALS (Material No. 05-047) along the axle of the bolt (96).

 (8)
 Install the bolt (96).

 (9)
 Install the washer (95).

 (10) Install the nut (94). TORQUE the nut (94) to to between 0.75 and 0.8 m.daN (66.37 and 70.79 lbf.in).
 NOTE : If you install a new bolt (96), drill a hole of dia 1.93 mm
____ (0.0759 in.) +0 mm (+0.0000 in.) +0.1 mm (+0.0039 in.).
 (11) Install a new cotter pin (93). Subtask 52-13-31-420-058
 G. Installation of the Fittings of the Guide Arms
 (Ref. Fig. 408/TASK 52-13-31-991-010)

 (1)
 Clean the contact surfaces between all the components with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003) if necessary.

 (2)
 Install the serrated plates (107) (104).

 1EFF : ALL 1 52-13-31Page 431 1 1 Aug 01/98R 1 1 1CES 1

 (3)
 Install the fitting swivel pieces (105) and (108).

 (4)
 Make sure that the slots of the swivel pieces are orientated in the aircraft centerline direction.

 (5)
 Install the bolts (106) and the washers (103).

 (6)
 Install the nuts (102) and tighten them.

 (7)
 Engage the guide arm fittings (100) and (101) (Ref. TASK 52-11-12-400-003).

 5. Close-up
________
 **ON A/C 001-002,

 Subtask 52-13-31-080-050
 A. Installation of Components
 (1)
 Remove the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) (Ref. TASK 52-10-00-080-001).

 (2)
 Install the door insulation.

 (3)
 Install the door frame lining panels (Ref. TASK 25-23-45-400-005) or (Ref. TASK 25-23-45-400-008).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(4)