(b)
 Remove the nut (233), the washers (231), the bush (227) and the bolt (230) from the intermediate lever (229).

 (c)
 Disconnect the eye-end of the connection rod (226) from the fork-end of the intermediate lever (229).

 1EFF : 301-399, 1 52-22-21Page 446 1 1 May 01/04 1 1 1CES 1

 Locking Hook and Drift Pin Assembly (73" Door)
 Figure 406/TASK 52-22-21-991-005

 1EFF : 301-399, 1 52-22-21Page 447 1 1 May 01/04 1 1 1CES 1

 (d) If required, remove the bush (228) from the fork-end of the intermediate lever (229).
 (2)
 Cut and discard the tie-wrap (224) and disassemble the bellows (223) from the door fitting (219).

 (3)
 Disconnect the locking hook (210) from the door fitting (219) as follows:

 (a)
 Remove the nut (217) and the bolt (221) together with the washer

 (220) from the door structure.

 (b)
 Hold the locking hook (210) and remove the sleeve (218) together with the washers (211) and (212) from the door fitting (219).

 (c)
 Remove the locking hook (210) together with the connection rod

 (226) and the bellows (223) from the door fitting (219).

 (4)
 If required, cut and discard the tie-wrap (222) and remove the bellows (223) from the connection rod (226).

 Subtask 52-22-21-020-059
 B. Removal of the Drift Pin Assembly
 (Ref. Fig. 406/TASK 52-22-21-991-005)

 (1)
 Disconnect the fork link (254) from the twin lever (262) as follows:

 (a)
 Remove and discard the cotter pin (251) from the nut (252).

 (b)
 Remove the nut (252), the washers (253), the bush (256) and the bolt (255) from the fork link (254).

 (c)
 Disconnect the fork link (254) from the twin lever (262) and hold the spacer (257).

 (d)
 If required, remove the bush (263) from the fork link (254).

 (2)
 Disconnect the fork link (254) from the drift pin (239) as follows:

 (a)
 Remove and discard the cotter pin (246) from the nut (247).

 (b)
 Remove the nut (247), the washers (248), the bush (241) and the bolt (249) from the fork link (254).

 (c)
 Disconnect the fork link (254) from the drift pin (239) and hold the spacer (242).

 1EFF : 301-399, 1 52-22-21Page 448 1 1 May 01/04 1 1 1CES 1

 (d) If required, remove the bush (250) from the fork link (254).
 (3)
 Remove the drift pin assembly (240) as follows:

 (a)
 Remove the washers (244) and the bolts (245) to disconnect the guide fitting (238) from the upper member (243).

 (b)
 Remove the drift pin assembly (240) from the upper member (243).

 (4)
 If required, remove the spring unit (275) as follows: WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE SPRING. THE

_______ TENSION IN THE SPRING CAN CAUSE INJURY TO PERSONS.
 (a)
 Remove and discard the cotter pin (266) from the nut (267).

 (b)
 Remove the washers (268), the bush (265) and the bolt (273) from the fitting (271).

 (c)
 Remove and discard the cotter pin (259) from the nut (258).

 (d)
 Remove the nut (258), the washers (260), the bush (264) and the bolt (261) from the twin lever (262).

 (e)
 Disconnect the spring unit (275) from the twin lever (262) and remove it from the fitting (271).

 (f)
 If required, remove the bush (276) from the fork-end of the twin lever (254).

 (g)
 If required, remove the nuts (272), the washers (270), the bolts

 (269) and the fitting (271) from the door structure.

 (h)
 If required, remove the bush (274) from the fork-end of the fitting (271).

 Subtask 52-22-21-020-060
 C. Removal of the Locking Shaft Assembly
 (Ref. Fig. 407/TASK 52-22-21-991-006)

 (1) Remove the locking indicator assembly (280) from the door structure as follows:
 (a)
 Remove and discard the cotter pin (284) from the pin (287).

 (b)
 Remove the washer (285) and the pin (287) from the joint (288).

 1EFF : 301-399, 1 52-22-21Page 449 1 1 May 01/04 1 1 1CES 1

 Locking Shaft Assembly (73" Door)
 Figure 407/TASK 52-22-21-991-006- 13 (SHEET 1)

 1EFF : 301-399, 1 52-22-21Page 450 1 1 May 01/04 1 1 1CES 1

　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(124)