(d)
 Install the washers (55) ,(54), (53) and (52) and the nut (51) on the transmission shaft (60).

 (e)
 Tighten the nut (51) and safety with a new cotter pin (50).

 (f)
 Make sure that the shaft levers (59) and (61) are correctly installed on their splines.

 (g)
 Attach the shaft lever (61) with the boltw (62) and the nut (67).

 (h)
 Install the new lockwasher (57) and the screw (58) to attach the shaft lever (59).

 (i)
 Tighten the screw (58) and safety it with the lockwasher (57).

 (2) Attach the push rods (1) and (68) to the shaft levers (59) and (61) as follows:
 (a)
 If removed, install the bushes (69) on the fork-end of the shaft levers (59) and (61).

 (b)
 Put the eye-ends of the push rods (1) and (68) in position to the fork-ends of the shaft levers (59) and (61).

 (c)
 Install the bolts (63), the washers (64), the bushes (70) and the nuts (66).

 (d) Tighten the nuts (66) and safety each with a new cotter pin (65). Subtask 52-22-22-720-051
 C. Do the functional test to make sure that the slide release mechanism operates satisfactorily (Ref. TASK 52-22-00-720-001).
 5. Close-up
________ Subtask 52-22-22-865-055
 A. Make sure that this(these) circuit breaker(s) is(are) closed:
 13WN, 15WN, 48WV

 1EFF : 301-399, 1 52-22-22Page 418 1 1 May 01/04 1 1 1CES 1 Subtask 52-22-22-410-053

 B. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the insulation mats in the door structure.

 (3)
 Install the door linings (Ref. TASK 25-23-47-400-012) and (Ref. TASK 25-23-47-400-013) as required.

 (4)
 Do the special precaution for the door damper and emergency operation cylinder (Ref. TASK 52-22-00-860-004).

 (5)
 Close applicable the door (Ref. TASK 52-22-00-410-001).

 (6)
 Remove the access platform(s).

 1EFF : 301-399, 1 52-22-22Page 419 1 1 May 01/04 1 1 1CES 1 TASK 52-22-22-000-003

 Removal of the Intermediate Shaft Assembly
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.2 m (10 ft. 6 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-000-012  Removal of the Door Linings of the LH FWD Emergency Exit Door, zone 231
 25-23-47-000-013  Removal of the Door Linings of the RH FWD Emergency Exit Door at zone 251 or RH AFT at zone 252 or LH AFT at zone 232.
 52-22-00-010-001 Opening of the Emergency Exit Doors from the Passenger Compartment 52-22-00-860-003 Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder 52-22-22-991-003 Fig. 403
 3. Job Set-up
__________
 Subtask 52-22-22-010-056
 A. Get Access
 (1)
 Open the applicable emergency exit door (referred to as door) as required (Ref. TASK 52-22-00-010-001).

 (2)
 Make sure that the access platform is in position below the partly opened door.

 1EFF : 301-399, 1 52-22-22Page 420 1 1 May 01/04 1 1 1CES 1

 (3) Make sure that the special precaution on the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).
 Subtask 52-22-22-865-056
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
 Subtask 52-22-22-010-052
 C. Get Access
 (1)
 Remove the door linings as required (Ref. TASK 25-23-47-000-012) (Ref. TASK 25-23-47-000-013) from the door.

 (2)
 Carefully disengage the VELCRO tapes and remove the insulation mat from the inner side of the door as required.

 4. Procedure
_________ Subtask 52-22-22-020-052
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(139)