NOTE : Make sure that the punch mark on each lever aligns with the notch
____
of the locking shaft during the installation.
(1)
If removed, install the stop fitting (205) with the bolts (204) and the nuts (206) to the door structure.
(2)
Put the locking shaft (176) in position to the door structure and assemble the target lever (173 on the locking shaft (176).
(3)
Install the flange bearing (202) as follows:
(a)
Put the flange bearing (202) in position to the door structure.
(b)
Make sure that flange bearing (202) engages with the end of the locking shaft (176).
(c)
Attach the flange bearing (202) with the bolts (203) and the nuts
(201) to the door structure.
(4)
Attach the support fitting (177) to the door structure as follows:
(a)
Make sure that the attachment holes of the support fitting (177) and the door structure are align.
(b)
Attach the support fitting (177) with the bolts (199) and (207) and the nuts (198) and (200).
(c)
Put the stop fitting (208) in position to the support fitting
(177) and attach it with the bolts (207) and (209) and the nuts
(198) and (200).
(5)
Turn the locking shaft (176) to make sure that it moves easily.
(6)
Put the target lever (173) in the correct position on the locking shaft (176) as follows:
(a) Move the the target lever (173) so that its attachment screw engages in the groove of the locking shaft (176).
NOTE : Make sure that the target lever (173) is in the correct
____ position to the related proximity sensor.
1EFF : 301-399, 1 52-22-21Page 441 1 1 May 01/04 1 1 1CES 1
(b) Tighten the attachment screw of the target lever (173).
(7)
Connnect the spring rod assembly (179) with the indication lever
(166) as follows:
WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE SPRING. THE
_______ TENSION IN THE SPRING CAN CAUSE INJURY TO PERSONS.
(a)
Put the fork-end of the spring rod assembly (179) in position to the indication lever (166) and attach it with the pin (178).
(b)
Safety the pin (178) with the washer (180) and the new cotter pin (181).
(8)
Connnect the spring unit (154) with the twin lever (152) as follows: WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE SPRING. THE
_______ TENSION IN THE SPRING CAN CAUSE INJURY TO PERSONS.
(a)
Put the eye-end of the spring unit (154) in position to the fork-end of the twin lever (152).
(b)
Install the bolt (151), the bushes (153), the washers (150) and the nut (148) to the twin lever (152).
(c)
Tighten the nut (148) and safety it with the new cotter pin (149).
(9) Connnect the fork link (139) with the twin lever (152) as follows:
(a)
If removed, install the bush (146) to the fork link (139).
(b)
Put the fork link (139) in position to the twin lever (152).
(c)
Install the bolt (147), the washers (1490, the spacer (145), the bush (144) and the nut (142) to the twin lever(152).
(d)
Tighten the nut (142) and safety it with the new cotter pin (141).
(10) Connnect the connection rod (118) with the actuation lever (123) as follows:
(a)
If removed, install the bush (120) to the actuation lever (123).
(b)
Put the eye-end of the connection rod (118) in position to the fork-end of the actuation lever (123).
1EFF : 301-399, 1 52-22-21Page 442 1 1 May 01/04 1 1 1CES 1
(c)
Install the bolt (122), the washers (121), the bush (119) and the nut (125) on the actuation lever (123).
(d)
Tighten the nut (125) and safety it with the new cotter pin (124).
(11)
Connnect the actuation rod (197) with the engaging lever (184) as follows:
(a)
If removed, install the bush (196) to the engaging lever (184).
(b)
Put the eye-end of the actuation rod (197) in position to the fork-end of the engaging lever (184).
(c)
Install the bolt (182), the washers (183), the bush (195) and the nut (185) to the engaging lever (184).
(d)
Tighten the nut (185) and safety it with the new cotter pin (186).
(12)
Connnect the push rod (190) with the engaging lever (184) as follows:
(a)
If removed, install the bush (192) to the engaging lever (184).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(122)
