A. Get Access
(1)
Remove the emergency exit hatch (referred to as hatch) (Ref. TASK 52-21-11-000-001).
(2)
If necessary, remove the lining from the applicable hatch (Ref. TASK 25-23-47-000-001).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 52-21-11Page 430 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
4. Procedure
_________
Subtask 52-21-11-020-051
A. Removal of the Slide Release Mechanism
**ON A/C 001-049, 051-099, 101-149, 201-299,
(Ref. Fig. 407/TASK 52-21-11-991-004) R **ON A/C 151-199, 401-499,
(Ref. Fig. 407A/TASK 52-21-11-991-004-A) R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(1)
Remove the nuts (24) and the bolts (23) from the edge curve of the hatch structure.
(2)
Remove the slide release mechanism (25) from the hatch structure.
(3)
If necessary, remove and discard the spring pin (26) from the guide fitting (22).
(4)
Remove the latch pin (20) and the spring (21) from the guide fitting (22).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 52-21-11Page 431 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Slide Release Mechanism
Figure 407/TASK 52-21-11-991-004
R 1EFF : 001-049, 051-099, 101-149, 201-299, 1 52-21-11Page 432 1 1 Aug 01/05 1 1 1CES 1
Slide Release Mechanism Figure 407A/TASK 52-21-11-991-004-A
R 1EFF : 151-199, 401-499, 1 52-21-11Page 433 1 1 Aug 01/05 1 1 1CES 1 TASK 52-21-11-400-003
Installation of the Slide Release Mechanism
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
Material No. 09-018 USA AMS 3267/3 CORROSION INHIBITING LOW ADHESION SEALANT (Ref. 20-31-00)
B. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
spring pin 52-21-11 35 -100
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-400-001 Installation of the Lining on the Emergency Exit Hatches
52-21-00-200-001 Detailed Visual Inspection of the Emergency Exits, Internal Structure and Load Transmitting Profile LH/RH
52-21-00-720-001 Functional Test of the Automatic and the Manual Slide Release Signal 52-21-11-400-001 Installation of the Emergency Exit Hatch
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 52-21-11Page 434 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 001-049, 051-099, 101-149, 201-299,
52-21-11-991-004 Fig. 407 R **ON A/C 151-199, 401-499,
52-21-11-991-004-A Fig. 407A R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
3. Job Set-up
__________
Subtask 52-21-11-100-050
A. Preparation for the Installation
(1)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(2)
Clean the component interface and/or the adjacent area.
(3)
For the opposide installation, remove the self-adhesive cover from the inner edge curve of the emergebcy exit hatch (referred to as hatch).
NOTE : In this case, you must also install the opposite guide fitting
____
(22).
(4)
Make sure that the new installation area is clean and in the correct condition.
(5)
Apply SEALANTS (Material No. 09-018) to the mating area of the guide fitting (22), the bolts (23) and the new spring pin (26).
(6)
Apply COMMON GREASE (Material No. 04-004) to the latch pin (20).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 52-21-11Page 435 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(36)
