3. Job Set-up
__________ Subtask 52-22-31-010-050
A. Get Access
(1)
Open the applicable emergency exit door (referred to as door) as required (Ref. TASK 52-22-00-010-001).
(2)
Make sure that the special precaution on the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).
(3)
Make sure that the access platform in position below the applicable door.
(4)
Remove the door linings as required (Ref. TASK 25-23-47-000-012) or (Ref. TASK 25-23-47-000-013).
(5)
Carefully disconnect the VELCRO-tapes and remove the insulation mat from the inner side of the door.
4. Procedure
_________ Subtask 52-22-31-020-050
A. Removal of the Adjustable Stops and Roller Guides
(Ref. Fig. 401/TASK 52-22-31-991-001)
(1)
Remove the adjustable stops (5) as follows:
(a)
If required, release the lock plate (4) and remove the nut (3), the lock washer (4) and the stop bolt (6) from the stop fitting (5).
(b)
Remove the nuts (2) and the bolts (1).
(c)
Remove the stop fitting (5) from the door member.
(2)
Remove the guide rollers (8) as follows:
(a)
Remove the nuts (9) and the bolts (7).
(b)
Remove the guide roller (8) from the door member.
1EFF : 301-399, 1 52-22-31Page 402 1 1 May 01/04 1 1 1CES 1
Adjustable Stops and Roller Guides at the Emergency Exit Door
Figure 401/TASK 52-22-31-991-001
1EFF : 301-399, 1 52-22-31Page 403 1 1 May 01/04 1 1 1CES 1
(3) Remove the roller guides (11) as follows:
(a)
Remove the nuts (12) and the bolts (10).
(b)
Remove the guide roller (11) from the door member.
1EFF : 301-399, 1 52-22-31Page 404 1 1 May 01/04 1 1 1CES 1
TASK 52-22-31-400-001 Installation of Adjustable Stops and Roller Guides at the Emergency Exit Door
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific wooden or plastic scraper
No specific access platform 3.20 m (10 ft. 6 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-013 USA MIL-PRF-81733 TYPE I CLASS A CORROSION INHIBITING BRUSH CONSISTENCY (Ref. 20-31-00)
Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
lock plate 52-22-31 01 -040
1EFF : 301-399, 1 52-22-31Page 405 1 1 May 01/04 1 1 1CES 1 D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-000-012 Removal of the Door Linings of the LH FWD Emergency Exit Door, zone 231
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(145)
