R 1EFF : ALL 1 52-42-18Page 408 1 1 Nov 01/03 1 1 1CES 1
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-28-00-912-004 Electrical Bonding of Components With Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)-
**ON A/C 001-001, 051-052,
52-42-18-991-001 Fig. 401 R **ON A/C 106-149, 219-299, 301-399, 401-499,
52-42-18-991-001-B Fig. 401A
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-218,
Post SB 53-1136 For A/C 001-001,051-052,
52-42-18-991-001-A Fig. 401B
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-218,
52-42-18-991-002 Fig. 402 R **ON A/C 106-149, 219-299, 301-399, 401-499,
52-42-18-991-002-A Fig. 402A
**ON A/C ALL
3. Job Set-up
__________
Subtask 52-42-18-869-050
A. Aircraft Maintenance Configuration
(1) Make sure that the access platform is in position at the zone 192.
1EFF : ALL 1 52-42-18Page 409 1 1 Aug 01/05 1 1 1CES 1 Subtask 52-42-18-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU FUEL/RFL/DFL/SPLY 2QU L24 122VU ELEC/RFL/SPLY/LOGIC 4PR U29
4. Procedure
_________
**ON A/C 001-001, 051-052,
(Ref. Fig. 401/TASK 52-42-18-991-001) R **ON A/C 106-149, 219-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 52-42-18-991-001-B)
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-218,
Post SB 53-1136 For A/C 001-001,051-052,
(Ref. Fig. 401B/TASK 52-42-18-991-001-A)
**ON A/C 001-001, 051-052,
Subtask 52-42-18-420-051
A. Installation of the door 192MB.
(1)
Put the door (8) in position in its frame on the hinge side.
(2)
Install the spring fitting (11) on the door (8).
(3)
Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-001) in the housing of the screws (16).
1EFF : ALL 1 52-42-18Page 410 1 1 Aug 01/05 1 1 1CES 1
(4) Install the cup washers (13), the washers (15) , the bolts (2) and
(16) and the nuts (3).
NOTE : Do an electrical bonding when you install the bolts (2), the
____ cup washers (13) and the nuts (3). (Ref. TASK 20-28-00-912-004)
(5) Tighten the nuts (3).
(6) Engage the spring (9) on the door frame fitting (1).
Subtask 52-42-18-820-050
B. Adjustment of the Proximity Switch (10).
(1)
Loosen the nut (4) and the locknut (6) of the stop screw (7).
(2)
Adjust the stop screw (7) so that it touches the proximity switch
(10) before the door (8) is closed.
(3)
Make sure that when the door is fully closed, the light is off.
(4)
Open the door (8).
(5)
Retract the stop screw by 2.5 +0.2 -0.2 mm (0.0984 +0.0078 -0.0078 in.).
(6)
Tighten the nut (4) and the locknut (6) on the support fitting (5).
(7)
Safety the nut (4) and the locknut (6) with MISCELLANEOUS (Material No. 19-010).
R **ON A/C 106-149, 219-299, 301-399, 401-499,
Subtask 52-42-18-420-051-B
A. Installation of the Door 192MB.
(1) Assembly of the door (4):
(a)
Put in position the pin (13) and install the axis (16) with the pin (17), the washers (14) and the new cotter pin (15).
(b)
Install the stop contactor (21) with the locknut (20), the washers (19) and the nut (18) on the support fitting (5).
R 1EFF : 001-001, 051-052, 106-149, 219-299, 1 52-42-18Page 411 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(2)
Hold the door in position and install the screws (9), the washers (7) and the new nuts (6) and tighten the nuts (6).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門7(10)
