52-42-23-991-002 Fig. 402 R **ON A/C 062-099, 104-149, 151-199, 204-299, 401-499,
52-42-23-991-002-A Fig. 402A
**ON A/C 301-399,
52-42-23-991-002-B Fig. 402B
**ON A/C ALL
3. Job Set-up
__________
Subtask 52-42-23-941-050
A. Make sure that the access platform is in position below the ground service panel door of the Yellow hydraulic system.
4. Procedure
_________
**ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 401/TASK 52-42-23-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 52-42-23-991-001-A)
1EFF : ALL 1 52-42-23Page 408 1 1 Aug 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-061, 101-103, 201-203,
Subtask 52-42-23-420-050
A. Installation of the Ground Service Panel Door of the Yellow Hydraulic System
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Put the access door (1) in the installation position.
(4)
Install the screws (2), the washers (5) and the nuts (6).
(5)
Install the bonding strap (7) (Ref. TASK 20-28-00-912-004).
(6)
If it was necessary to remove the spring bolt assembly, install it as follows:
(a)
Make sure that all parts of the removed spring bolt assembly are clean and in the correct condition.
(b)
Make sure that the bearing flange assy (18) and the hinge (3) are clean and in the correct condition.
(c)
Install the spring bolt (12) with the pin (19) and the retaining ring (8) at the hinge (3).
(d)
Put the compression spring (14) and the guide (16) in position on the spring bolt (12).
(e)
Install the guide (16) with the washers (15), the pin (17) and the retaining ring (13) at the bearing flange assy (18).
(7)
If it was necessary to remove the hinges (3) and (4), install them as follows:
(a)
Make sure that the support fitting assemblies (11) are clean and in the correct condition.
(b)
Install the hinges (3) and (4) with the pins (10) and the retaining rings (9) at the support fitting assemblies (11).
(c)
Connect the spring bolt assembly with the pin (19) and the retaining ring (8).
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 52-42-23Page 409 1 1 May 01/05 1 1 1CES 1R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
Subtask 52-42-23-420-050-A
A. Installation of the Ground Service Panel Door of the Yellow Hydraulic System
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
If removed, assemble the hinges (3) on the ground service panel and attach it with the screws (5) and the washers (4).
(4)
Put the access door (2) on the hinges (3) and attach it with the the bolts (9), the washers (10) and the nuts (11).
(5)
Put the bonding strap (6) on the upper hinge (3) and attach it with the bolt (1), the washer (7) and the nut (8) (Ref. TASK 20-28-00-912-004).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 52-42-23-820-050
B. Adjustment of the Ground Service Panel Door of the Yellow Hydraulic System
(1)
Carefully close and lock the access door (1).
(2)
Make sure that the values of the permitted contour offset and the gap between the access door (1) and the panel 198BB are in the limits.
**ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 402/TASK 52-42-23-991-002) R **ON A/C 062-099, 104-149, 151-199, 204-299, 401-499,
(Ref. Fig. 402A/TASK 52-42-23-991-002-A)
1EFF : ALL 1 52-42-23Page 410 1 1 Aug 01/05 1 1 1CES 1
Adjustment of the Ground Service Panel Door of the Yellow Hydraulic System
Figure 402/TASK 52-42-23-991-002
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 52-42-23Page 411 1 1 May 01/05 1 1 1CES 1
Adjustment of the Ground Service Panel Door of the Yellow Hydraulic System
Figure 402A/TASK 52-42-23-991-002-A
R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 52-42-23Page 412 1401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(3)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門7(17)
