(3)
Put the pin (13) in position and install the screw (3), the spacer
(2) and the nut (1).
(4)
Install the bonding lead (11), the washer (10) and the new nut (12) . NOTE : Do an electrical bonding when you install bonding lead (11),
____ the washer (10) and the nut (12). (Ref. TASK 20-28-00-912-004)
Subtask 52-42-18-820-050-B
B. Adjustment of the Proximity Switch (8).
(Ref. Fig. 402A/TASK 52-42-18-991-002-A)
(1)
Loosen the nut (18) and the locknut (20) of the stop contactor (21).
(2)
Adjust the stop contactor (21) so that it touches the proximity switch (8) before the door (4) is closed.
(3)
Make sure that when the door is fully closed, the light is off.
(4)
Open the door (4).
(5)
Retract the stop contactor (21) by 2.5 +0.2 -0.2 mm (0.0984 +0.0078 -0.0078 in.).
(6)
Tighten the nut (18) and the locknut (20) on the support fitting (5).
(7) Safety the nut (18) and the locknut (20) with MISCELLANEOUS (Material No. 19-010). R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-218,
R Post SB 53-1136 For A/C 001-001,051-052, Subtask 52-42-18-420-051-A
A. Installation of the Door 192MB.
(1)
Put the door (10) in position in its frame on the hinge side.
(2)
Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-001) in the housing of the screws (18).
1EFF : ALL 1 52-42-18Page 412 1 1 May 01/05 1 1 1CES 1
Adjustment of the Fuel Panel Access-Door (192MB)
Figure 402/TASK 52-42-18-991-002
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 52-42-18Page 413 1201-218, 1May 01/05 1 1 1CES 1
Adjustment of the Fuel Panel Access-Door (192MB)
Figure 402A/TASK 52-42-18-991-002-A
R 1EFF : 106-149, 219-299, 301-399, 401-499, 1 52-42-18Page 414 1 1 Aug 01/05 1 1 1CES 1
(3) Install the cup washers (2), the washers (17) , the screws (1) and
(18) and the nuts (8).
NOTE : Do an electrical bonding when you install the screws (1), the
____ cup washers (2) and the nuts (8). (Ref. TASK 20-28-00-912-004)
(4)
Tighten the nuts (8).
(5)
Install the screw (4), the washers (5) and (6), the spring (3), the washer (7) and (16) and the nut (15) on the fitting (9).
(6) Tighten the nut (15). Subtask 52-42-18-820-050-A
B. Adjustment of the Proximity Switch (19).
(1)
Loosen the nut (14) and the locknut (13) and the stop screw (14).
(2)
Adjust the stop screw (14) so that it touches the proximity switch
(19) before the door (10) is closed.
(3)
Make sure that when the door is fully closed, the light is off.
(4)
Open the door (10).
(5)
Retract the stop screw (14) by 2.5 +0.2 -0.2 mm (0.0984 +0.0078 -0.0078 in.).
(6)
Tighten the nut (11) and the locknut (13) on the support fitting (12).
(7)
Safety the nut (11) and the locknut (13) with MISCELLANEOUS (Material No. 19-010).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 52-42-18Page 415 1201-218, 1May 01/05 1 1 1CES 1 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-218,
Subtask 52-42-18-220-050
C. Check of the Peripheral Clearance.
(Ref. Fig. 402/TASK 52-42-18-991-002)
(1)
Close the door.
(2)
Do a check of the peripheral clearance between the door and the door frame: Clearance Y is 1.5 -0.5 +0.5 mm (0.0590 -0.0196 +0.0196 in.).
R **ON A/C 106-149, 219-299, 301-399, 401-499,
Subtask 52-42-18-220-050-A
C. Check and Adjustment of the Access Door
(Ref. Fig. 402A/TASK 52-42-18-991-002-A)
(1)
Apply paste in the recess of the hook (22).
(2)
Close the access door (4).
(3)
Make sure that:
(a)
the clearance J2 between the access door (4) and the access panels around the access door, is 1.5 +1.5 -0.5 mm (0.0590 +0.0590 -0.0196 in.)
(b)
the out-of-flush clearance J3 between the access door (4) and the access panels around the access door, is:
-
0 +0.7 -0.7 mm (0.0000 +0.0275 -0.0275 in.) acrros the line of fligt.
-
0 +1 -1 mm (0.0000 +0.0393 -0.0393 in.) in the line of flight.
(c)
the access door (2) is correctly installed on its frame.
(4)
Open the access door (2).
(5)
Make sure that the clearance J3 between the latch (11) and the ramp
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM DOORS 艙門7(11)
