(2)
Make sure that there is no:
(a)
Corrosion damage:
-If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200-P.Block001) for types of corrosion, inspection, removal and corrosion protection.
(b)
Other damage (cracks, scratches, stress, marks dents, bumps,...):
-if you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100-P.Block001) for damage classification and corrective action.
5. Close-up
________
Subtask 54-51-00-420-060
A. Installation of the Component
(1) Install the engine (Ref. TASK 71-00-00-400-042).
R Mating Face of the Pylon Pyramid Figure 626/TASK 54-51-00-991-039
1EFF : 1 1 1CES ALL 1 111 54-51-00 Page A633 Feb 01/04
Subtask 54-51-00-410-075
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
1EFF : ALL 1 54-51-00Page A634 1 1 Feb 01/04R 1 1 1CES 1
TASK 54-51-00-200-026
Detailed Inspection of Pylon, Engine Aft Attachment Beam Mating Face with the Engine Aft Mount Fitting
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 545171-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
No specific access platform 3 m (9 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R 1EFF : ALL 1 54-51-00Page A635 1 1 Feb 01/04 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-00-00-000-042 Removal of the Power Plant
71-00-00-400-042 Installation of the Power Plant
SRM 511100-P.Block001
SRM 512200-P.Block001
R 54-51-00-991-040 Fig. 627
3. Job Set-up
__________
Subtask 54-51-00-941-076
A. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
On the overheat maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b)
Put a warning notice to tell persons not to energize the FADEC. Subtask 54-51-00-010-070
B. Get Access
(1)
Put an access platform in position at the zone 415 (425).
Subtask 54-51-00-020-060
C. Removal of the Component
(1) Remove the engine (Ref. TASK 71-00-00-000-042).
R 1EFF : ALL 1 54-51-00Page A636 1 1 Feb 01/04 1 1 1CES 1
Subtask 54-51-00-110-077
D. Cleaning of the Structure
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Clean the inspection area with CLEANING AGENTS (Material No. 11-004) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003), if necessary.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NACELLES/PYLONS(50)
