2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-90-00-810-801 Failure of an Alternating Current Supply (ACS)
AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2)
AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2)
AMM 27-94-34-000-001 Removal of the SEC (1CE1,1CE2,1CE3)
AMM 27-94-34-400-001 Installation of the SEC (1CE1,1CE2,1CE3)
AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
ASM 27-93/07
3. Fault Confirmation
__________________
A. Test
(1) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).
4. Fault Isolation
_______________
A. If the ground scanning gives at least two maintenance messages of the list below: ELAC1 MON OR WIRING FROM THS ACTR XDCR2 9CE ELAC1 OR WIRING FROM L ELEV POS MON XDCR ELAC1 OR WIRING FROM R ELEV POS MON XDCR ELAC1 OR WIRING FROM L G ELEV MODE XDCR 34CE1 ELAC1 OR WIRING FROM R Y ELEV MODE XDCR 34CE2
(1) Remove the ELAC1 (Ref. AMM TASK 27-93-34-000-001) and the SEC1 (Ref. AMM TASK 27-94-34-000-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-90-00∞∞∞∞∞∞∞∞∞∞Page 226
May 01/04R
CES
(2) At the ELAC1 receptacle, do a check of the resistance between the pin AB/7K and the pin AB/8K (Ref. ASM 27-93/07):
(a) If the resistance is less than 10 Ohms:
1 Do this procedure (Ref. TASK 27-90-00-810-801).
_
2 Replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and
_ (Ref. AMM TASK 27-93-34-400-001).
3 Replace the SEC-1 (1CE1) (Ref. AMM TASK 27-94-34-000-001) and
_ (Ref. AMM TASK 27-94-34-400-001).
(b) If the resistance is more than 10 Ohms:
- do a check of the wiring of the ACS1 SPLY signal from the ELAC1 MON side to the COM side (Ref. ASM 27-93/07): . pins AE/1J and AE/1K to pins AE/10B and AE/11B of ELAC1 MON side . pins AE/10A and AE/11A of the ELAC1 MON side to pins AB/7J and AB/8J of the ELAC1 COM side.
1 If the wiring is not correct:
_
- repair it
- install the ELAC1 (Ref. AMM TASK 27-93-34-400-001) and the SEC1 (Ref. AMM TASK 27-94-34-400-001).
a If the fault continues:
_
- replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001).
2 If the wiring is correct:
_ a Replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001)
_ and (Ref. AMM TASK 27-93-34-400-001).
b Install the SEC1 (Ref. AMM TASK 27-94-34-400-001).
_
c If the fault continues:
_
- do a check and repair the wiring of the ACS1 SPLY MON signal from the ELAC1 COM side to the first terminal block, pins AB/7K and AB/8K (Ref. ASM 27-93/07).
B. Do the test given in para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-90-00∞∞∞∞∞∞∞∞∞∞Page 227
May 01/04R CES
Loss of the ACS1 of the ELAC1 COM and MON Sides
1. Possible Causes
_______________
- ELAC-1 (2CE1)
- SEC-1 (1CE1)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-90-00-810-811 Loss of the ACS1 Signal of the ELAC1 COM Side
27-90-00-810-812 Loss of the ACS1 Signal of the ELAC1 MON Side
AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2)
AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2)
AMM 27-94-34-000-001 Removal of the SEC (1CE1,1CE2,1CE3)
AMM 27-94-34-400-001 Installation of the SEC (1CE1,1CE2,1CE3)
AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
3. Fault Confirmation
__________________
A. Test
(1) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).
4. Fault Isolation
_______________
A. If the ground scanning gives at least two maintenance messages of the two lists below: First list:
- ELAC1 COM OR WIRING FROM THS ACTR XDCR2 9CE
- ELAC1 OR WIRING FROM L B ELEV POS XDCR 34CE3 中國(guó)航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 飛行操縱 2(100)
