2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 27-51-34-000-001 Removal of the SFCC (21CV,22CV)
 AMM 27-51-34-400-001 Installation of the SFCC (21CV,22CV)
 AMM 32-31-71-000-001 Removal of the LGCIU (5GA1, 5GA2)
 AMM 32-31-71-400-001 Installation of the LGCIU (5GA1, 5GA2)
 AWM 32-61-05
 AWM 32-61-06

 3. Fault Confirmation
__________________
 A. Message Analysis.
 (1) Access the submenu page "SYSTEM DATA FLAP" and press the line key "2L".
 (a) The page shown is the "ARINC 429 INPUT STATUS" and is refreshed every 5 seconds.
 NOTE : Refer to page block 301 for example of FLAP ARINC INPUT
____
 STATUS page.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 266
 May 01/04R CES

 (b) If the ARINC INPUT STATUS page shows LGCIU LABEL *** NO DATA, do the fault isolation.
 (2) If the ARINC INPUT STATUS page shows LGCIU 1 (2) OK.
 (a) Do the SFCC 1 (2) Reset and Initialization.

 B. Table of the circuit breakers used in this procedure:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
 4. Fault Isolation
_______________
 A. SFCC Reset and Initialization.
 (1) At the circuit breakers.
 (a) Open the circuit breakers.

 (b) Wait for 3 seconds and close the circuit breakers.

 (c) Wait for 60 seconds

 (d) Check the UPPER ECAM and the SD FLT/CTL page for the fault warnings.

 (e) If the ECAM warning clears, access the FLP ON GROUND FAULTS page and make sure that the ground log is clear.

 (f) If the checks at Para.4.A.(1)(e) are satisfactory there is no further maintenance action.

 B. Procedure,
 (1) Swap the LGCIU 1 with LGCIU 2 (Ref. AMM TASK 32-31-71-000-001) (Ref. AMM TASK 32-31-71-400-001).

 (2) Access the submenu page "SYSTEM DATA FLAP" and press the line key "2L".

 (a) The page shown is the "ARINC 429 INPUT STATUS" and is refreshed every 5 seconds.

 (b) If the ARINC INPUT STATUS page shows "LGCIU 1 (2) OK",then the initial LGCIU 1 (2) is at fault.

 (3) Install the LGCIU 1 and 2 in their initial locations and replace the unserviceable LGCIU-1 (5GA1) LGCIU-2 (5GA2) . Refer to Para. 4.B.(1).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 267
 May 01/04R CES

 (4) Go to the submenu page "SYSTEM DATA FLAP" and access the "ARINC 429 INPUT STATUS"page.

 (a) If the fault remains in the SFCC 1 (2) the fault is in the SFCC 1
 (2) interface/circuit.

 (5) Swap the SFCC 1 (2) with SFCC 2 (1) (Ref. AMM TASK 27-51-34-000-001) (Ref. AMM TASK 27-51-34-400-001).

 (6) Go to the submenu page "SYSTEM DATA FLAP" and access the "ARINC 429 INPUT STATUS"page, SFCC 1 and then SFCC 2.

 (a) If the fault moves with the SFCC 1 (2) to the SFCC 2 (1) position, the fault is in the SFCC 1 (2) input interface.

 (7) Instal the SFCC 1 and 2 in their initial locations and replace the unserviceable SFCC-1 (21CV) SFCC-2 (22CV) Refer to Para. 4.A.(3).

 (a) Do Para. 4.A.(6). If the fault remains in the SFCC 1 (2) interface/circuit.

 (8) Do a check of the aircraft wiring between the LGCIU 1 ARINC connector and the SFCC 1 (2) ARINC electrical connecter. (Ref. AWM 32-61-05) (Ref. AWM 32-61-06).

 (9) If there is a fault repair the wiring/interface.

 (10) Do the BITE test as in Para. 3.A.(2) and Para. 3.A.(4).
 (a) Set the MCDU to MENU MODE and access the FLAP ON GROUND FAULTS page and make sure that the ground log is clear.
 5. Close-up
________
 A. Put the aircraft back to its initial configuration.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 268
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 2(3)