Loss of the ACS2 Signal of the SEC3 MON Side
 1. Possible Causes
_______________
 - SEC-3 (1CE3)

 - wiring of the ACS2 signal from the SEC3 MON side to the first terminal block

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-90-00-810-801 Failure of an Alternating Current Supply (ACS)
 AMM 27-94-34-000-001 Removal of the SEC (1CE1,1CE2,1CE3)
 AMM 27-94-34-400-001 Installation of the SEC (1CE1,1CE2,1CE3)

R  AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning) ASM 27-94/04
 3. Fault Confirmation
__________________
 A. Test Do the BITE Test of the EFCS (Ground Scanning) (Ref. AMM TASK 27-96-00-740-001).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance messages:
 L SPLR2 POS XDCR 31CE3
 and
 R SPLR2 POS XDCR 31CE4

 - remove the SEC3 (Ref. AMM TASK 27-94-34-000-001).
 (1) At the SEC3 receptacle, do a check of the resistance and of the insulation between the pin AD/10H and the pin AD/10G (15 to 250 ohms) (Ref. ASM 27-94/04).
 (a) If the resistance values are in the specified limits:

 - replace the SEC-3 (1CE3) (Ref. AMM TASK 27-94-34-000-001) and (Ref. AMM TASK 27-94-34-400-001).

 (b) If the resistance is less than 15 ohms:

 1  Do the trouble shooting procedure (Ref. TASK 27-90-00-810-
_
 801).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-90-00∞∞∞∞∞∞∞∞∞∞Page 212
 Aug 01/99 CES 2 Replace the SEC-3 (1CE3) (Ref. AMM TASK 27-94-34-000-001) and

_ (Ref. AMM TASK 27-94-34-400-001).
 (c) If the resistance is more than 250 ohms: 1 Do a check and repair the wiring of the ACS2 signal from the
_
 SEC3 MON side to the first terminal block (Ref. ASM 27-94/04). 2 Install the SEC3 (Ref. AMM TASK 27-94-34-400-001).
_ R B. Do the test given in para. 3.

 Loss of the ACS2 Signal of the ELAC1 COM Side
 1. Possible Causes
_______________
 - ELAC-1 (2CE1)

 - wiring of the ACS2 signal from the ELAC1 COM side to the first terminal block

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-90-00-810-801 Failure of an Alternating Current Supply (ACS)
 AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2)
 AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2)
 AMM 27-96-00-710-020 Operational Test of the Side Stick Assembly

 (Activation for the BITE Test)
 AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
 ASM 27-93/02

 3. Fault Confirmation
__________________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 A. Test
 Not applicable, you cannot confirm this fault on the ground.

 **ON A/C 301-399,
 A. Test
 (1) Do the operational test of the side stick assembly (activation for the BITE test) (Ref. AMM TASK 27-96-00-710-020).

 (2) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).

 4. Fault Isolation
_______________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 A. If the POST FLIGHT REPORT (PFR) gives the maintenance messages: L B AIL POS XDCR 33CE3 and R G AIL POS XDCR 33CE2
 - remove the ELAC1 (Ref. AMM TASK 27-93-34-000-001).
 (1) At the ELAC1 receptacle, do a check of the resistance and of the insulation between the pin AA/14A and the pin AA/14B (15 to 250 ohms) (Ref. ASM 27-93/02).
 (a) If the resistance values are in the specified limits:

 - replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001).

 (b) If the resistance is less than 15 ohms:

 1 Do the trouble shooting procedure (Ref. TASK 27-90-00-810-
_
 801).

 2 Replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and
　
中國(guó)航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 飛行操縱 2(96)