(Activation for the BITE Test)
AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
ASM 27-93/02
3. Fault Confirmation
__________________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
A. Test
Not applicable, you cannot confirm this fault on the ground.
**ON A/C 301-399,
A. Test
(1) Do the operational test of the side stick assembly (activation for the BITE test) (Ref. AMM TASK 27-96-00-710-020).
(2) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).
4. Fault Isolation
_______________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
A. If the POST FLIGHT REPORT (PFR) gives the maintenance messages: L B AIL MODE XDCR 33CE3 OR INPUT OF ELAC1 and R G AIL MODE XDCR 33CE4 OR INPUT OF ELAC1
- remove the ELAC1 (Ref. AMM TASK 27-93-34-000-001).
(1) At the ELAC1 receptacle, do a check of the resistance and of the insulation between the pin AD/2C and the pin AD/2D (15 to 250 ohms) (Ref. ASM 27-93/02).
(a) If the resistance values are in the specified limits:
- replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001).
(b) If the resistance is less than 15 ohms:
1 Do the trouble shooting procedure (Ref. TASK 27-90-00-810-
_
801).
2 Replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and
_ (Ref. AMM TASK 27-93-34-400-001).
(c) If the resistance is more than 250 ohms:
1 Do a check and repair the wiring of the ACS2 signal from the
_ ELAC1 MON side to the first terminal block (Ref. ASM 27-93/02).
2 Install the ELAC1 (Ref. AMM TASK 27-93-34-400-001).
_
**ON A/C 301-399,
A. If the test gives the maintenance messages:
L B AIL MODE XDCR 33CE3 OR INPUT OF ELAC1
and
R G AIL MODE XDCR 33CE4 OR INPUT OF ELAC1
- remove the ELAC1 (Ref. AMM TASK 27-93-34-000-001).
R (1) At the ELAC1 receptacle, do a check of the resistance and of the
R insulation between the pin AD/2C and the pin AD/2D (15 to 250 ohms)
R (Ref. ASM 27-93/02).
R (a) If the resistance values are in the specified limits:
R - replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and
R (Ref. AMM TASK 27-93-34-400-001).
R (b) If the resistance is less than 15 ohms:
R 1_ Do the trouble shooting procedure (Ref. TASK 27-90-00-810-
R 801).
R 2_ Replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and
R (Ref. AMM TASK 27-93-34-400-001).
R (c) If the resistance is more than 250 ohms:
R 1_ Do a check and repair the wiring of the ACS2 signal from the
R ELAC1 MON side to the first terminal block (Ref. ASM 27-
R 93/02).
R 2_ Install the ELAC1 (Ref. AMM TASK 27-93-34-400-001).
R B. Do the test given in para. 3.
R **ON A/C ALL
TASK 27-90-00-810-810
Loss of the ACS2 Signal of the ELAC2 MON Side
1. Possible Causes
_______________
- ELAC-2 (2CE2)
- wiring of the ACS2 signal from the ELAC2 MON side to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-90-00-810-801 Failure of an Alternating Current Supply (ACS)
AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2)
AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2)
AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
ASM 27-93/03
3. Fault Confirmation
__________________
A. Test Do the BITE Test of the EFCS (Ground Scanning) (Ref. AMM TASK 27-96-00-740-001).
4. Fault Isolation
_______________
A. If the test gives the maintenance messages:
L G AIL MODE XDCR 33CE1 OR INPUT OF ELAC2
and
R G AIL MODE XDCR 33CE4 OR INPUT OF ELAC2
- remove the ELAC2 (Ref. AMM TASK 27-93-34-000-001).
(1) At the ELAC2 receptacle, do a check of the resistance and of the insulation between the pin AD/2C and the pin AD/2D (15 to 250 ohms) (Ref. ASM 27-93/03).
(a) If the resistance values are in the specified limits:
- replace the ELAC-2 (2CE2) (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001). 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 2(98)
