(1) If the fault continues:
- do a check and repair the wiring of the POS XDCR SPLY signal from the servo control (31CE3) to the first terminal block, (Ref. ASM 27-94/04).
(2) If the fault continues:
- do a check and repair the wiring of the POS XDCR V1, V2 signals from the servo control (31CE3) to the first terminal block, (Ref. ASM 27-94/04).
B. Do the tests given in Para. 3.
Loss of the Left Spoiler 2 Position Signal for the SEC 3
1. Possible Causes
_______________
- SEC-3 (1CE3)
- wiring of the ANI 2-6 signal from the SEC 3 (1CE3) to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 27-94-34-000-001 Removal of the SEC (1CE1,1CE2,1CE3)
AMM 27-94-34-400-001 Installation of the SEC (1CE1,1CE2,1CE3)
AMM 27-96-00-710-020 Operational Test of the Side Stick Assembly
(Activation for the BITE Test) R AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning) ASM 27-94/04
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the side stick assembly (activation for BITE test) (Ref. AMM TASK 27-96-00-710-020).
(2) Do the BITE test of the EFCS (Ground scanning) (Ref. AMM TASK 27-96-00-740-001).
4. Fault Isolation
_______________
A. If the BITE test gives the maintenance message:
SEC 3 COM OR WIRING FROM L SPLR 2 POS XDCR 31CE3
or
SEC 3 MON OR WIRING FROM L SPLR 2 POS XDCR 31CE3
- replace the SEC-3 (1CE3), (Ref. AMM TASK 27-94-34-000-001) and (Ref. AMM TASK 27-94-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the ANI 2-6 signal from the SEC 3 (1CE3) to the first terminal block COM part or MON part as shown in the maintenance message (Ref. ASM 27-94/04).
B. Do the tests given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-60-00∞∞∞∞∞∞∞∞∞∞Page 236
May 01/00 CES Loss of the Right Spoiler 2 Position Signal for the SEC 3
1. Possible Causes
_______________
- SEC-3 (1CE3)
- wiring of the ANI 2-7 signal from the SEC 3 (1CE3) to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 27-94-34-000-001 Removal of the SEC (1CE1,1CE2,1CE3)
AMM 27-94-34-400-001 Installation of the SEC (1CE1,1CE2,1CE3)
AMM 27-96-00-710-020 Operational Test of the Side Stick Assembly
(Activation for the BITE Test) R AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning) ASM 27-94/04
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the side stick assembly (activation for BITE test) (Ref. AMM TASK 27-96-00-710-020).
(2) Do the BITE test of the EFCS (Ground scanning) (Ref. AMM TASK 27-96-00-740-001).
4. Fault Isolation
_______________
A. If the BITE test gives the maintenance message:
SEC 3 COM OR WIRING FROM R SPLR 2 POS XDCR 31CE4
or
SEC 3 MON OR WIRING FROM R SPLR 2 POS XDCR 31CE4
- replace the SEC-3 (1CE3), (Ref. AMM TASK 27-94-34-000-001) and (Ref. AMM TASK 27-94-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the ANI 2-7 signal from the SEC 3 (1CE3) to the first terminal block COM part or MON part as shown in the maintenance message (Ref. ASM 27-94/04).
B. Do the tests given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-60-00∞∞∞∞∞∞∞∞∞∞Page 237
May 01/00 CES Failure of the Right Spoiler 2 Position Transducer
1. Possible Causes
_______________
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 2(38)
