Loss of the Lower ECAM DU
1. Possible Causes
_______________
- DU-ECAM, LOWER (4WT2)
- CTL PNL-ECAM (6WT)
- DMC-3 (1WT3)
- DMC-2 (1WT2)
- wiring
- C/B-EIS/ECAM DU/LOWER/SPLY (13WT2)
- C/B-EIS/ECAM DU/LOWER/SWTG (24WT2)
- RELAY-BUS1 TO ESS BUS SWTG, DMC3 (26WT)
- C/B-EIS/DMC3/SPLY (10WT3)
- C/B-EIS/DMC3/SWTG (21WT3)
- SEL SW-EIS DMC (18WT)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-860-001 EIS Start Procedure
AMM 31-60-00-860-002 EIS Stop Procedure
AMM 31-61-12-000-001 Removal of the ECAM Control Panel (6WT)
AMM 31-61-12-400-001 Installation of the ECAM Control Panel (6WT)
AMM 31-63-22-000-001 Removal of the Display Unit
(2WT1,2WT2,3WT1,3WT2,4WT1,4WT2)
AMM 31-63-22-400-001 Installation of the Display Unit
(2WT1,2WT2,3WT1,3WT2,4WT1,4WT2)
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
ASM 31-61/02
ASM 31-68/01
ASM 31-68/02
3. Fault Confirmation
__________________
A. Job Set-up Do the EIS start procedure (lower ECAM DU only) (Ref. AMM TASK 31-60-00-860-001).
B. Test
Make sure that the lower ECAM DU stays off.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 230
201-299, 301-399, Aug 01/05 CES
4. Fault Isolation
_______________
A. If the lower ECAM DU stays off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at NORM:
(1) Do a check for 115VAC at pin AA/104 of the lower ECAM DU (4WT2) (Ref. ASM 31-61/02).
(a) If there is no 115VAC:
- replace the DU-ECAM, LOWER (4WT2) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(b) If there is 115VAC:
- do a check for a ground signal at pin AA/102 of the lower ECAM DU (4WT2).
1_ If there is no ground signal:
- repair the wiring from lower ECAM DU (4WT2) pin AA/102 to
the ground terminal.
2 If there is a ground signal:
_
- do a check of the wiring from lower ECAM DU (4WT2) pin AA/104 to the circuit breaker (13WT2).
a If there is no continuity:
_ - repair the wiring.
b If there is continuity:
_ - replace the C/B-EIS/ECAM DU/LOWER/SPLY (13WT2).
(2) If the fault continues:
- do a check of the wiring from lower ECAM DU (4WT2) pins AA/49, 50, 51 to ECAM control panel (6WT) pins B/B, C, U (Ref. ASM 31-68/01).
(a) If there is continuity:
- replace the DU-ECAM, LOWER (4WT2) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
1 If the fault continues:
_
- replace the CTL PNL-ECAM (6WT) (Ref. AMM TASK 31-61-12-000-001) and (Ref. AMM TASK 31-61-12-400-001).
(b) If there is no continuity:
- repair the wiring from lower ECAM DU (4WT2) pins AA/49, 50, 51 to ECAM control panel (6WT) pins B/B, C, U.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 231
201-299, 301-399, Aug 01/05 CES
B. If the lower ECAM DU stays off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at F/O/3:
(1) Do a check for 28VDC at pin AA/93 on the lower ECAM DU (4WT2) (Ref. ASM 31-61/02).
(a) If there is 28VDC:
- replace the DU-ECAM, LOWER (4WT2) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(b) If there is no 28VDC:
- do a check for a ground signal at pin AA/106 of the lower ECAM DU (4WT2).
1 If there is no ground signal:
_
- repair the wiring from lower ECAM DU (4WT2) pin AA/106 to the ground terminal.
2 If there is a ground signal:
_
- do a check of the wiring from lower ECAM DU (4WT2) pin AA/93 to the circuit breaker (24WT2).
a If there is no continuity:
_ - repair the wiring.
b If there is continuity: 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 指示和記錄系統(tǒng) 3(109)
