「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-81∞∞∞∞∞∞∞∞∞∞Page 262
Feb 01/05R CES
2 If there is continuity:
_
- do a check of the wiring from DMC1 (1WT1) pins AB/10B, 10C to the first terminal block (Ref. ASM 31-61/04).
a If there is no continuity:
_ - repair the wiring.
b If there is continuity:
_
- do a check and repair the wiring from DMC1 (1WT1) pins AB/10D, 10E to the first terminal block (Ref. ASM 31-61/04).
(2) If this test gives no maintenance message:
- replace the PFD-CAPT (2WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(a) If the fault continues:
- do a check of the wiring from CAPT PFD (2WT1) pins AA/21, 22 to the first terminal block (Ref. ASM 31-61/04).
1 If there is no continuity:
_ - repair the wiring.
2 If there is continuity:
_
- do a check and repair the wiring from CAPT PFD (2WT1) pins AA/23, 24 to the first terminal block (Ref. ASM 31-61/04).
B. If the EIS DMC selector switch (18WT) on the panel 8VU is at F/O/3 and the test gives the maintenance message DMC3 : ALT DSPLY ERR MSG: - on the panel 500VU, push the F/O PFD/ND XFR pushbutton switch (9WT2)
- do the test given in Para. 3.
(1) If this test gives the maintenance message DMC3 : ALT DSPLY ERR:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check of the wiring from the DMC3 (1WT3) to the DMC2 (1WT2): . pins AB/9B, 9C to pins AB/10J, 10H . pins AB/9D, 9E to pins AB/10F, 10G (Ref. ASM 31-61/04).
1 If there is no continuity:
_ - repair the wiring.
2 If there is continuity:
_
- do a check of the wiring from DMC2 (1WT2) pins AB/10B, 10C to the first terminal block (Ref. ASM 31-61/04).
a If there is no continuity:
_ - repair the wiring.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-81∞∞∞∞∞∞∞∞∞∞Page 263
Feb 01/05R CES
b_ If there is continuity:
- do a check and repair the wiring from DMC2 (1WT2) pins
AB/10D, 10E to the first terminal block (Ref. ASM 31-
61/04).
(2) If this test gives no maintenance message:
- replace the PFD-F/O (2WT2) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(a) If the fault continues:
- do a check of the wiring from F/O PFD (2WT2) pins AA/21, 22 to the first terminal block (Ref. ASM 31-61/04).
1 If there is no continuity:
_ - repair the wiring.
2 If there is continuity:
_
- do a check and repair the wiring from F/O PFD (2WT2) pins AA/23, 24 to the first terminal block (Ref. ASM 31-61/04).
C. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-81∞∞∞∞∞∞∞∞∞∞Page 264
Feb 01/05R
CES Loss of the DSDL PFD MASTER or DSDL PFD FDBK Bus Detected by the DMC3
1. Possible Causes
_______________
- DMC-3 (1WT3)
- PFD-CAPT (2WT1)
- PFD-F/O (2WT2)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-740-002 EIS Input Test
AMM 31-63-22-000-001 Removal of the Display Unit
(2WT1,2WT2,3WT1,3WT2,4WT1,4WT2)
AMM 31-63-22-400-001 Installation of the Display Unit
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 3(16)
