- replace the DMC-2 (1WT2) and the DU-ECAM, LOWER (4WT2) (Ref. AMM TASK 31-63-34-000-001) (Ref. AMM TASK 31-63-34-400-001) (Ref. AMM TASK 31-63-22-000-001) (Ref. AMM TASK 31-63-22-400-001)
 B. Do the EIS system test (Ref. AMM TASK 31-60-00-740-004)
 (1) If the test gives the maintenance message DU ND CAPT(3WT1)/DMC2(1WT2)
 - replace the ND-CAPT (3WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001) Feedack Message from the DMC2 on the CAPT PFD DU

 1. Possible Causes
_______________
 - DMC-2 (1WT2)

 - ND-F/O (3WT2)

 - PFD-CAPT (2WT1)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-740-004 EIS System Test AMM 31-63-22-000-001 Removal of the Display Unit (2WT1,2WT2,3WT1,3WT2,4WT1,4WT2) AMM 31-63-22-400-001 Installation of the Display Unit
 (2WT1,2WT2,3WT1,3WT2,4WT1,4WT2) AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3) AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
 3. Fault Confirmation
__________________
 A. Test
 - Not applicable, the fault cannot be confirmed.
 4. Fault Isolation
_______________
 A. Read the Post Flight Report
 (1) If the PFR gives the maintenance message:
 DMC2(1WT2)/DU ND FO(3WT2)/DU PFD CAPT(2WT1)

 - replace the DMC-2 (1WT2) and the ND-F/O (3WT2) (Ref. AMM TASK 31-63-34-000-001) (Ref. AMM TASK 31-63-34-400-001) (Ref. AMM TASK 31-63-22-000-001) (Ref. AMM TASK 31-63-22-400-001)
 B. Do the EIS system test (Ref. AMM TASK 31-60-00-740-004)
 (1) If the test gives the maintenance message DU PFD
 CAPT(2WT1)/DMC2(1WT2)

 - replace the PFD-CAPT (2WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001)

 DISPLAY MANAGEMENT COMPUTER (DMC) - FAULT ISOLATION PROCEDURES
______________________________________________________________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
 TASK 31-63-82-810-801
 Loss of the CAPT PFD, CAPT ND and Upper ECAM DU
 1. Possible Causes
_______________
 - DMC-1 (1WT1)

 - DMC-3 (1WT3)

 - wiring

 - C/B-EIS/DMC1/SPLY (10WT1)

 - C/B-EIS/DMC3/SWTG (21WT3)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-860-001 EIS Start Procedure
 AMM 31-60-00-860-002 EIS Stop Procedure
 AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
 AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
 ASM 31-61/02

 3. Fault Confirmation
__________________
 A. Job Set-up Do the EIS start procedure (CAPT PFD, CAPT ND and upper ECAM DU only) (Ref. AMM TASK 31-60-00-860-001).
 B. Test
 Make sure that the display units stay off.

 4. Fault Isolation
_______________
 A. If the three display units stay off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at NORM:
 (1) Do a check for 115VAC at pin AC/2 of the DMC1 (1WT1) (Ref. ASM 31-61/02).
 (a) If there is 115VAC:
 - replace the DMC-1 (1WT1) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 201
 Aug 01/05 CES (b) If there is no 115VAC:

 - do a check for a ground signal at pin AC/7 of the DMC1 (1WT1). 1 If there is no ground signal:
_

 - repair the wiring from DMC1 (1WT1) pin AC/7 to the ground terminal.
 2 If there is a ground signal:
_

 - do a check of the wiring from DMC1 (1WT1) pin AC/2 to the circuit breaker (10WT1).
 a If there is no continuity:
_

 - repair the wiring. b If there is continuity:
_

 - replace the C/B-EIS/DMC1/SPLY (10WT1).
 B. If the three display units stay off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at CAPT/3:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 3(98)