3. Fault Confirmation
__________________
A. Job Set-up
(1) Do the EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
- Set the selector switch EIS DMC-SEL SW (18WT) on F/O 3 position
4. Fault Isolation
_______________
A. Make sure that:
- the INVALID DATA message is shown on the FO PFD DU and on the FO ND DU
- the ECAM warning EIS DMC 3 FAULT is shown on the upper ECAM display
(1) Replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(2) If the fault continues:
- Make sure that there is 115VAC on the pin AC-2 of the DMC3(1WT3)
(a) If there is no 115VAC at pin AC-2:
- check and repair the wiring from the DMC3(1WT3) pin AC-2 to the pin A2 switching relay - DMC3 (26WT)
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 401-499, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 278
Aug 01/05 CES 1 if there is continuity:
_
- make sure there is 115VAC on the pins A1 and A3 of the relay SWTG-DM3 (26WT) (Ref. ASM 31-62/01) . if there is no 115VAC on the pin A1 of the relay
- check and repair the wiring from the switching relay-DMC3 (26WT) pin A1 to the EIS DMC3 STBY/SPLY circuit breaker (14WT1) . . if there is no continuity from the relay 26WT to the C/B 14WT1:
- replace the EIS/DMC3/STBY/SPLY (14WT1) (Ref. ASM 31-61/02) . if there is no 115VAC on the pin A3 of the relay
- check and repair the wiring from the switching relay-DMC3 (26WT) pin A3 to the EIS DMC3/SPLY circuit breaker (10WT3) . . if there is no continuity from the relay 26WT to the C/B 10WT3:
- replace the EIS/DMC3/SPLY (10WT3) (Ref. ASM 31-61/02) . if there is 115VAC on pins A1 and A3 of the switching relay-DMC3 (26WT):
- replace the RELAY-BUS1 TO ESS BUS SWTG, DMC3 (26WT) (Ref. ASM 31-61/02)
(b) If there is 115VAC at pin AC-2 of the DMC3:
- Make sure that there is a ground signal at pin AC-7 of the DMC3(1WT3)
1 if there is no ground signal:
_
- repair the wiring from the DMC3 (1WT3) pin AC-7 to the ground terminal (Ref. ASM 31-62/01).
B. Do the EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).
Loss of the ARINC 629 link from the CAPT DU's to the DMC3
1. Possible Causes
_______________
- DMC-3 (1WT3)
- EIS/DMC3/STBY/SPLY (14WT1)
- EIS/DMC3/SPLY (10WT3)
- RELAY-BUS1 TO ESS BUS SWTG, DMC3 (26WT)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-860-001 EIS Start Procedure AMM 31-60-00-860-002 EIS Stop Procedure AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3) AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3) ASM 31-61/02 ASM 31-62/01
3. Fault Confirmation
__________________
A. Job Set-up
(1) Do the EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
- Set the selector switch EIS DMC-SEL SW (18WT) on CAPT/3 position
4. Fault Isolation
_______________
A. Make sure that:
- the INVALID DATA message is shown on the CAPT PFD DU and on the CAPT ND DU
- the ECAM warning EIS DMC 3 FAULT is shown on the upper ECAM display
(1) Replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(2) If the fault continues:
- Make sure that there is 115VAC on the pin AC-2 of the DMC3(1WT3)
(a) If there is no 115VAC at pin AC-2:
- check and repair the wiring from the DMC3(1WT3) pin AC-2 to the pin A2 of the switching relay - DMC3 (26WT) 1 if there is continuity:
_
- make sure there is 115VAC on the pins A1 and A3 of the relay SWTG-DM3 (26WT) (Ref. ASM 31-62/01) . if there is no 115VAC on the pin A1 of the relay
- check and repair the wiring from the switching relay-DMC3 (26WT) pin A1 to the EIS DMC3 STBY/SPLY circuit breaker (14WT1) . . if there is no continuity from the relay 26WT to the C/B 14WT1:
- replace the EIS/DMC3/STBY/SPLY (14WT1) (Ref. ASM 31-61/02) . if there is no 115VAC on the pin A3 of the relay
- check and repair the wiring from the switching relay-DMC3 (26WT) pin A3 to the EIS DMC3/SPLY circuit breaker (10WT3) . . if there is no continuity from the relay 26WT to the C/B 10WT3: 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 3(124)
