「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-81∞∞∞∞∞∞∞∞∞∞Page 274
 Feb 01/05R CES

 2 If there is continuity:
_

 - do a check of the wiring from the DMC1 (1WT1) pins AB/11B, 11C to the first terminal block (Ref. ASM 31-61/04).
 a If there is no continuity:
_ - repair the wiring.

 b If there is continuity:
_

 - do a check and repair the wiring from the DMC1 (1WT1) pins AB/11D, 11E to the first terminal block (Ref. ASM 31-61/04).
 (2) If this test gives no maintenance message:
 - replace the DU-ECAM, UPPER (4WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
 (a) If the fault continues:
 - do a check of the wiring from the upper ECAM DU (4WT1) pins AA/35, 36 to the first terminal block (Ref. ASM 31-61/04).
 1 If there is no continuity:
_ - repair the wiring.

 2 If there is continuity:
_

 - do a check and repair the wiring from the upper ECAM DU (4WT1) pins AA/38, 39 to the first terminal block (Ref. ASM 31-61/04).
 B. Do the test given in Para. 3.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-81∞∞∞∞∞∞∞∞∞∞Page 275
 Feb 01/05R
 CES  Loss of the ENG1 Fuel Flow (FF) Indication on the Upper ECAM DU Detected by the DMC3

 1. Possible Causes
_______________
 - DMC-3 (1WT3)

 - DU-ECAM, UPPER (4WT1)

 - wiring

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-740-002 EIS Input Test
 AMM 31-63-22-000-001 Removal of the Display Unit
 (2WT1,2WT2,3WT1,3WT2,4WT1,4WT2)
 AMM 31-63-22-400-001 Installation of the Display Unit

 (2WT1,2WT2,3WT1,3WT2,4WT1,4WT2)
 AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
 AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
 ASM 31-61/04

 3. Fault Confirmation
__________________
 A. Test
 Do the EIS input test (Ref. AMM TASK 31-60-00-740-002).

 4. Fault Isolation
_______________
 A. If the test gives the maintenance message DMC3 : ENG1 FF DSPLY ERR:
 - on the ECAM control panel (6WT), set the UPPER DISPLAY potentiometer to OFF
 - do the test given in Para. 3.
 (1) If this test gives the maintenance message DMC3 : ENG1 FF DSPLY ERR:
 - replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
 (a) If the fault continues:
 - do a check of the wiring from the DMC3 (1WT3) to the DMC1 (1WT1): . pins AB/11B, 11C to pins AB/11J, 11H . pins AB/11D, 11E to pins AB/11F, 11G (Ref. ASM 31-61/04).
 1 If there is no continuity:
_ - repair the wiring.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-81∞∞∞∞∞∞∞∞∞∞Page 276
 Feb 01/05R CES

 2 If there is continuity:
_

 - do a check of the wiring from the DMC1 (1WT1) pins AB/11B, 11C to the first terminal block (Ref. ASM 31-61/04).
 a If there is no continuity:
_ - repair the wiring.

 b If there is continuity:
_

 - do a check and repair the wiring from the DMC1 (1WT1) pins AB/11D, 11E to the first terminal block (Ref. ASM 31-61/04).
 (2) If this test gives no maintenance message:
 - replace the DU-ECAM, UPPER (4WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
 (a) If the fault continues:
 - do a check of the wiring from the upper ECAM DU (4WT1) pins AA/35, 36 to the first terminal block (Ref. ASM 31-61/04).
 1 If there is no continuity:
_ - repair the wiring.

 2 If there is continuity:
_

 - do a check and repair the wiring from the upper ECAM DU (4WT1) pins AA/38, 39 to the first terminal block (Ref. ASM 31-61/04).
 B. Do the test given in Para. 3.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-81∞∞∞∞∞∞∞∞∞∞Page 277
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統(tǒng) 3(20)