1. Possible Causes
_______________
 -BMC-1 (1HA1)

 -CABLE-CONNECTING, ENG 1 PYLON (2HF1)
 -SNSG ELEM-OVHT, ENG 1 PYLON (1HF1)
 -CABLE ASSY (3HF1)
 -ducts
 -seals

 -
wiring between the pin 5B of the BMC1 connector (1HA1-AA) and the cable 2HF1

 -
wiring between the pin 6B of the BMC1 connector (1HA1-AA) and the cable 3HF1

 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
9240SI 1 LOOP CONTROLLER
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 36-11-34-000-001 Removal of the BMC (1HA1, 1HA2)
 AMM 36-11-34-400-001 Installation of the BMC (1HA1, 1HA2)
 AMM 36-22-15-000-001 Removal of the Pylon Overheat Sensing Element (1HF1,

 1HF2) AMM 36-22-15-400-001 Installation of the Pylon Overheat Sensing Element (1HF1, 1HF2) ASM 36-22/01
 3. Fault Confirmation
__________________
 A. Test

 (1)
 Start the APU.

 (2)
 On the AIR control panel 30VU, push the APU BLEED pushbutton switch.

 1
 -EFF : ALL

-∞∞36-22-00∞∞∞∞∞∞∞∞∞∞Page 205
 --Feb 01/03R ---CES -

 4. Fault Isolation
_______________

 A. If the fault is confirmed (ENG BLEED LEAK warning):
 -do a leakage check of the ducting.
 (1)
 If the duct is cracked/damaged:

 -replace the defective ducts.

 (2)
 If there are leaks on the seals:

 -replace the defective seals.
 NOTE : If there are no air leaks, replace the seals (to prevent
____ leaks).
 B. If no leak warning comes into view:
 -remove the BMC1 (1HA1) (Ref. AMM TASK 36-11-34-000-001)
 - on the shelf 95VU, connect the LOOP CONTROLLER (9240SI) between the connector 1HA1-AA/5B and the ground (Ref. ASM 36-22/01)
 -do a check of the impedance read on the LOOP CONTROLLER (9240SI).
 (1)
 If the impedance is more than 3 KOhms:

 -disconnect the LOOP CONTROLLER (9240SI) from the BMC1 connector
 -replace the BMC-1 (1HA1) which is removed (Ref. AMM TASK 36-11-34-000-001) and (Ref. AMM TASK 36-11-34-400-001).
 -refer to Para. 4.C.

 (2)
 If the impedance is less than 3 KOhms:

 -disconnect the LOOP CONTROLLER (9240SI) from the BMC1 connector
 -do a visual inspection of the sensing elements and cables on the engine 1 pylon loop.
 (a)
 If a sensing element or cable is damaged:

 -replace the sensing element or cable (Ref. AMM TASK 36-22-15-000-001) and (Ref. AMM TASK 36-22-15-400-001)
 -disconnect the LOOP CONTROLLER (9240SI) from the BMC1 connector
 -install the BMC1 (Ref. AMM TASK 36-11-34-400-001)
 -refer to Para. 4.C.

 (b)
 If no sensing element is damaged:

 -disconnect the connector between the cable 2HF1 and the sensing element 1HF1
 -connect the LOOP CONTROLLER (9240SI) between the connector 1HA1-AA/5B and the ground
 -do a check of the impedance read on the LOOP CONTROLLER (9240SI).
 1_ If the impedance is less than 3 KOhms:
 - replace the CABLE-CONNECTING, ENG 1 PYLON (2HF1) (Ref. AMM
 TASK 36-22-15-000-001) and (Ref. AMM TASK 36-22-15-400-001)
 - do a check of the impedance read on the LOOP CONTROLLER
 (9240SI).

 1
 -EFF : ALL

-∞∞36-22-00∞∞∞∞∞∞∞∞∞∞Page 206
 --Feb 01/03R ---CES -

 2
_

 a_ If the impedance is less than 3 KOhms:
 - do a check and repair the wiring between the pin 5B of
 the BMC1 connector (1HA1-AA) and the cable 2HF1
 - connect all the cables or connectors disconnected
 - disconnect the LOOP CONTROLLER (9240SI) from the BMC1
 connector
 - install the BMC1 (1HA1) (Ref. AMM TASK 36-11-34-400-001)
 - refer to Para. 4.C.

 b If the impedance is more than 3 KOhms:
_ -connect all the cables or connectors disconnected
 -disconnect the LOOP CONTROLLER (9240SI) from the BMC1 connector
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 PNEUMATIC(112)