-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page A276
--Feb 01/05R ---CES -
4. Fault Isolation
_______________
A. If the test gives a maintenance message, you can find the related trouble shooting procedure in the (Ref. TSM 36 PB 101).
(1) If there is no maintenance message:
-replace the VALVE-BLEED PRESS REG (4001HA) (Ref. AMM TASK 36-11-52-000-040) and (Ref. AMM TASK 36-11-52-400-040).
(a) If the fault continues:
-replace the SOLENOID-BLEED PRESS REG V CTL, ENG 1 (10HA1) (Ref. AMM TASK 36-11-55-000-001) and (Ref. AMM TASK 36-11-55-400-001).
1_ If the fault continues:
- replace the XDCR-BLEED TRANSFER PRESS, ENG 1 (7HA1) (Ref.
AMM TASK 36-11-15-000-001) and (Ref. AMM TASK 36-11-15-400-
001).
a If the fault continues:
_
-do a check and repair the wiring: . from the FULLY CLOSED signal of the BMC1 (1HA1) to the bleed pressure-regulator valve (4001HA) . from pin A/3 of the bleed pressure-regulator valve (4001HA) to the first terminal block (Ref. ASM 36-11/01).
B. After the subsequent flight, make sure that the fault does not continue.
1
-EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page A277
--Feb 01/05R ---CES -
The Bleed Pressure-Regulator Valve of the Engine 1 is Shown Closed Amber on the Lower ECAM DU
1. Possible Causes_______________
-XDCR-BLEED TRANSFER PRESS, ENG 1 (7HA1)
-VALVE-BLEED PRESS REG (4001HA)
-SOLENOID-BLEED PRESS REG V CTL, ENG 1 (10HA1)
-sense line
-wiring
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 36-11-00-720-007 Functional Test of the Sense Lines Upstream of the Bleed Pressure Regulator Valve (4001HA) and Connected to the Control Solenoid (10HA1,10HA2)
AMM 36-11-00-740-001 BITE Test of the BMC 1(2)
AMM 36-11-15-000-001 Removal of the Bleed Transferred Pressure Transducer (7HA1,7HA2)
AMM 36-11-15-400-001 Installation of the Bleed Transferred Pressure Transducer (7HA1,7HA2)
AMM 36-11-15-720-001 Functional Test of the Bleed Transferred Pressure Transducer (7HA1,7HA2)
AMM 36-11-52-000-040 Removal of the Bleed Pressure-Regulator Valve (4001HA)
AMM 36-11-52-400-040 Installation of the Bleed Pressure-Regulator Valve (4001HA)
AMM 36-11-55-000-001 Removal of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2)
AMM 36-11-55-400-001 Installation of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2)
ASM 36-11/01
TSM 36 PB 101
3. Fault Confirmation__________________
A. Test
(1) Do the BITE test of the BMC1 (Ref. AMM TASK 36-11-00-740-001).
1
-EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page A278
--Feb 01/05R ---CES -
4. Fault Isolation
_______________
A. If the test gives a maintenance message, you can find the related trouble shooting procedure in the (Ref. TSM 36 PB 101).
(1) If there is no maintenance message:
-do the functional test of the bleed transferred pressure transducer (7HA1) (Ref. AMM TASK 36-11-15-720-001).
(a)
If the test is not OK:
-replace the XDCR-BLEED TRANSFER PRESS, ENG 1 (7HA1) (Ref. AMM TASK 36-11-15-000-001) (Ref. AMM TASK 36-11-15-400-001).
(b)
If the test is OK:
-replace the VALVE-BLEED PRESS REG (4001HA) (Ref. AMM TASK 36-11-52-000-040) and (Ref. AMM TASK 36-11-52-400-040).
1_ If the fault continues:
- replace the SOLENOID-BLEED PRESS REG V CTL, ENG 1 (10HA1)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 PNEUMATIC(79)
