*
do a check and repair the wiring between the ENG 1 BLEED pushbutton switch to the circuit breaker (3HA1), pin A/D2 to pin 2.
C. If the test gives the maintenance message: PRESS REG-V 4001HA1 OR SOL 10HA1 OR SENSE LINE
-do the trouble shooting procedure for the Bleed Pressure Regulator Valve (4001HA) and the Bleed Pressure Regulator Solenoid (10HA1) (Ref. TASK 36-11-00-810-829)
D. Do the test given in para. 3.
1
-EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 265
--Feb 01/05R ---CES -
Loss of the Manual Electrical Closure of the Bleed Pressure-Regulator Valve of the Engine 2
1. Possible Causes_______________
-VALVE-BLEED PRESS REG (4001HA)
-BMC-2 (1HA2)
-SOLENOID-BLEED PRESS REG V CTL, ENG 2 (10HA2)
-wiring
-P/BSW-ENG 2 BLEED (4HA2)
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 36-11-34-000-001 Removal of the BMC (1HA1, 1HA2)
AMM 36-11-34-400-001 Installation of the BMC (1HA1, 1HA2)
AMM 36-11-52-000-040 Removal of the Bleed Pressure-Regulator Valve (4001HA)
AMM 36-11-52-400-040 Installation of the Bleed Pressure-Regulator Valve (4001HA)
AMM 36-11-52-720-001 Functional Test of the Opening of the Bleed Pressure Regulator Valve
AMM 36-11-55-000-001 Removal of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2)
AMM 36-11-55-400-001 Installation of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2)
ASM 36-11/02
TSM 36-11-00-810-830 Loss of the Non Return Function and Temperature Limitation Function of the Bleed Pressure-Regulator Valve of the Engine 2
3. Fault Confirmation__________________
A. Test
(1) Do the test of the bleed pressure-regulator valve (Ref. AMM TASK 36-11-52-720-001).
1
-EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 266
--Feb 01/05R ---CES -
4. Fault Isolation
_______________
A. Table of the circuit breakers used in this procedure:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------122VU AIR BLEED/ENG 2/CTL 3HA2 Z23 122VU AIR BLEED/ENG 2/MONG 2HA2 Z22
B. If the fault symptom is identified by the maintenance message:
PRESS REG-V 4001HA2 OR SOL 10HA2
-do a check of the visual position indicator of the bleed
pressure-regulator valve.
(1)
If the bleed pressure-regulator valve is open:
-replace the VALVE-BLEED PRESS REG (4001HA) (Ref. AMM TASK 36-11-52-000-040) and (Ref. AMM TASK 36-11-52-400-040).
(2)
If the bleed pressure-regulator valve is closed:
-make sure that the indication of the valve position on the lower ECAM display unit is correct when you manually operate the valve shaft.
(a) If the indication does not agree with the position of the valve butterfly:
1 Do a check and repair the wiring between the bleed pressure
_ regulator-valve (4001HA) to the BMC2 (1HA2), pin A/5 to pin AA/2B (Ref. ASM 36-11/02).
2 If the fault continues:
_
-replace the BMC-2 (1HA2) (Ref. AMM TASK 36-11-34-000-001) and (Ref. AMM TASK 36-11-34-400-001).
(b) If the fault continues:
-release the ENG 2 BLEED pushbutton switch
-make sure that the bleed pressure-regulator valve control-solenoid (10HA2) makes clicks.
1 If the solenoid makes clicks:
_
-do a check and clean the sense line between the bleed pressure-regulator valve control-solenoid (10HA2) and the bleed pressure-regulator valve (4001HA).
a If the fault continues:
_
-replace the VALVE-BLEED PRESS REG (4001HA).
b If the fault continues:
_
-replace the SOLENOID-BLEED PRESS REG V CTL, ENG 2 (10HA2) (Ref. AMM TASK 36-11-55-000-001) and (Ref. AMM TASK 36-11-55-400-001).
1
-EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 267
--Feb 01/05R ---CES -
2_ If the solenoid does not make clicks:
- do a check for 28VDC at pin A/1 of the connector of the
中國(guó)航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) PNEUMATIC(41)
