-replace the VALVE-HP BLEED (4000HA) (Ref. AMM TASK 36-11-51-000-040) and (Ref. AMM TASK 36-11-51-400-040).
(b)
If the position on the lower ECAM display unit is correct with the position indicator:
-connect the TEST SET - ENGINE BLEED SYSTEM (98D36003000000) or TEST SET - ENGINE BLEED SYSTEM (98F36003002000) to pressurize at 20 psi (1.3789 bar) the test port of the HP Bleed valve.
1 Make sure that there are no leaks at the sense line between
_ the HP bleed valve and the bleed pressure regulator valve and to the HP bleed valve closure control solenoid (11HA1).
2 Depressurize the system on the test set.
_
3 Remove the TEST SET - ENGINE BLEED SYSTEM (98D36003000000) or
_ TEST SET - ENGINE BLEED SYSTEM (98F36003002000).
a If there are leaks:
_
-repair the sense line
b If there are no leaks:
_
-replace the VALVE-HP BLEED (4000HA) (Ref. AMM TASK 36-11-51-000-040) and (Ref. AMM TASK 36-11-51-400-040).
If the fault continues:
1 -EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 279
--Aug 01/05 ---CES -
-
replace the SOL-HP BLEED OVERRIDE, ENG1 (11HA1) (Ref. AMM TASK 36-11-58-000-001) and (Ref. AMM TASK 36-11-58-400-001)
If the fault continues:
-
replace the XDCR-BLEED TRANSFER PRESS, ENG 1 (7HA1), (Ref. AMM TASK 36-11-15-000-001) and (Ref. AMM TASK 36-11-15-400-001).
If the fault continues:
-do a check and repair the wiring from the HP bleed valve to the BMC1, pins A/1 and A/5 to pins AA/14A and AA/15A (Ref. ASM 36-11/01).
R
-refer to Para. 4.B.
**ON A/C ALL
B. Test
(1)
Do the engine 1 start procedure (Ref. AMM TASK 71-00-00-710-003).
(2)
Make sure that the ECAM warning AIR ENG 1 HP VALVE FAULT is not shown on the upper ECAM DU.
1 -EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 280
--Aug 01/05 ---CES - Failure of the HP Bleed Valve of the Engine 2 Blocked in the Closed Position
1. Possible Causes
_______________
-VALVE-HP BLEED (4000HA)
-XDCR-BLEED TRANSFER PRESS, ENG 2 (7HA2)
-SOL-HP BLEED OVERRIDE, ENG2 (11HA2)
-sense line
-wiring
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) 98D36003000000 1 TEST SET - ENGINE BLEED SYSTEM 98F36003002000 1 TEST SET - ENGINE BLEED SYSTEM
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 36-11-15-000-001 Removal of the Bleed Transferred Pressure Transducer (7HA1,7HA2) AMM 36-11-15-400-001 Installation of the Bleed Transferred Pressure
Transducer (7HA1,7HA2) AMM 36-11-51-000-040 Removal of the High Pressure Bleed Valve (4000HA) AMM 36-11-51-400-040 Installation of the High Pressure Bleed Valve
(4000HA) AMM 36-11-58-000-001 Removal of the HP Bleed Override Solenoid (11HA1, 11HA2) AMM 36-11-58-400-001 Installation of the HP Bleed Override Solenoid
(11HA1, 11HA2) AMM 71-00-00-710-003 Engine Automatic Start ASM 36-11/02
3. Fault Confirmation
__________________
A. Test
(1) Not Applicable
1
-EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 281
--Feb 01/05R ---CES -
4. Fault Isolation
_______________
R **ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
A. If the fault symptom is identified by the maintenance message: HP BLEED-V 4000HA2 OR SENSE LINE
-do a check of the unions of the sense line at the bleed pressure-regulator valve (4001HA) and at the HP bleed valve (4000HA).
(1)
If the unions are loose:
-tighten these unions again (to 1.6 m.daN (11.79 lbf.ft)) and refer to Para. 4B.
(2)
If the unions are correct:
-make sure that the indication of the HP bleed valve position on the lower ECAM display unit is correct when you manually operate the valve shaft.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 PNEUMATIC(46)
