-replace the VALVE-HP BLEED (4000HA) (Ref. AMM TASK 36-11-51-000-040) and (Ref. AMM TASK 36-11-51-400-040).

 (b)
 If the position on the lower ECAM display unit is correct with the position indicator:

 -connect the TEST SET - ENGINE BLEED SYSTEM (98D36003000000) or TEST SET - ENGINE BLEED SYSTEM (98F36003002000) to pressurize at 20 psi (1.3789 bar) the test port of the HP bleed valve.
 1 Make sure that there are no leaks at the sense line between
_ the HP bleed valve and the bleed pressure regulator valve.
 2 Depressurize the system on the test set.
_
 3 Remove the TEST SET - ENGINE BLEED SYSTEM (98D36003000000) or
_ TEST SET - ENGINE BLEED SYSTEM (98F36003002000).
 a If there are leaks:
_
 -repair the sense line
 b If there are no leaks:
_
 -
replace the VALVE-HP BLEED (4000HA) (Ref. AMM TASK 36-11-51-000-040) and (Ref. AMM TASK 36-11-51-400-040).

 If the fault continues:

 -
replace the XDCR-BLEED TRANSFER PRESS, ENG 2 (7HA2), (Ref. AMM TASK 36-11-15-000-001) and (Ref. AMM TASK 36-11-15-400-001).

 If the fault continues:
 1 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 282
 --May 01/05 ---CES -

 -do a check and repair the wiring from the HP bleed valve to the BMC2, pins A/1 and A/5 to pins AA/14A and AA/15A (Ref. ASM 36-11/02).
 -refer to Para. 4B.
R **ON A/C 151-199, 401-499,
 A. If the fault symptom is identified by the maintenance message: HP BLEED-V 4000HA2 OR SENSE LINE
 -do a check of the unions of the sense line from the bleed pressure-regulator valve (4001HA) and the HP bleed valve (4000HA) and to the HP bleed valve closure control solenoid (11HA2).
 (1)
 If the unions are loose:

 -tighten these unions again (to 1.6 m.daN (11.79 lbf.ft)) and refer to Para. 4B.

 (2)
 If the unions are correct:

 -make sure that the indication of the HP bleed valve position on the lower ECAM display unit is correct when you manually operate the valve shaft.
 (a)
 If the position on the lower ECAM display unit is different with the position indicator:

 -replace the VALVE-HP BLEED (4000HA) (Ref. AMM TASK 36-11-51-000-040) and (Ref. AMM TASK 36-11-51-400-040).

 (b)
 If the position on the lower ECAM display unit is correct with the position indicator:

 -connect the TEST SET - ENGINE BLEED SYSTEM (98D36003000000) or TEST SET - ENGINE BLEED SYSTEM (98F36003002000) to pressurize at 20 psi (1.3789 bar) the test port of the HP Bleed valve.
 1 Make sure that there are no leaks at the sense line between
_ the HP bleed valve and the bleed pressure regulator valve and to the HP bleed valve closure control solenoid (11HA2).
 2 Depressurize the system on the test set.
_
 3 Remove the TEST SET - ENGINE BLEED SYSTEM (98D36003000000) or
_ TEST SET - ENGINE BLEED SYSTEM (98F36003002000).
 a If there are leaks:
_
 -repair the sense line
 b If there are no leaks:
_
 -replace the VALVE-HP BLEED (4000HA) (Ref. AMM TASK 36-11-51-000-040) and (Ref. AMM TASK 36-11-51-400-040).
 If the fault continues:
 1 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 283

 --Aug 01/05 ---CES -

 -
replace the SOL-HP BLEED OVERRIDE, ENG2 (11HA2) (Ref. AMM TASK 36-11-58-000-001) and (Ref. AMM TASK 36-11-58-400-001)

 If the fault continues:

 -
replace the XDCR-BLEED TRANSFER PRESS, ENG 2 (7HA2), (Ref. AMM TASK 36-11-15-000-001) and (Ref. AMM TASK 36-11-15-400-001).

 If the fault continues:

 -do a check and repair the wiring from the HP bleed valve to the BMC2, pins A/1 and A/5 to pins AA/14A and AA/15A (Ref. ASM 36-11/02).
 -refer to Para. 4.B.
 **ON A/C ALL
 B. Test

 (1)
 Do the engine 2 start procedure (Ref. AMM TASK 71-00-00-710-003).

 (2)
 Make sure that the ECAM warning AIR ENG 2 HP VALVE FAULT is not shown on the upper ECAM DU.

 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 284
 --Feb 01/05R ---CES -

 HP Bleed Valve Locked in the Not Fully Open Position on the Engine 1
 WARNING : MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 PNEUMATIC(47)