(b)
If the fault continues:
-replace the VALVE-HP BLEED (4000HA) (Ref. AMM TASK 36-11-51-000-040) and (Ref. AMM TASK 36-11-51-400-040).
(c)
If the fault continues:
-do a check and clean the sense line between the bleed pressure-regulator valve (4001HA), the HP bleed valve (4000HA) and the associated solenoid (11HA2).
1 -EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 273
--Aug 01/05 ---CES - (d) If the fault continues:
-replace the VALVE-BLEED PRESS REG (4001HA) (Ref. AMM TASK 36-11-52-000-040) and (Ref. AMM TASK 36-11-52-400-040).
**ON A/C ALL
B. Do the test given in para. 3.
1
-EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 274
--Feb 01/05R ---CES -
HP Bleed Valve of the Engine 1 Blocked in the Open Position
1. Possible Causes
_______________
-VALVE-HP BLEED (4000HA)
-
wiring
-
wiring between pin A/3 of the HP bleed valve and the ground terminal
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 36-11-51-000-040 Removal of the High Pressure Bleed Valve (4000HA) AMM 36-11-51-400-040 Installation of the High Pressure Bleed Valve (4000HA) ASM 36-11/01
3. Fault Confirmation
__________________
A. Not applicable.
4. Fault Isolation
_______________
A. If the fault symptom is identified by the maintenance message:
HP BLEED-V 4000HA1
-make sure that the indication of the position of the HP bleed valve on the lower ECAM display unit is correct when you manually operate the valve shaft.
(1) If the indication does not agree with the position of the valve butterfly:
-do a check and repair the wiring from the HP bleed valve to the BMC1, pin A/1 to pin AA/14A and pin A/5 to pin AA/15A (Ref. ASM 36-11/01).
(a)
If the fault continues:
-do a check and repair the wiring between pin A/3 of the HP bleed valve and the ground terminal.
(b)
If the fault continues:
-replace the VALVE-HP BLEED (4000HA) (Ref. AMM TASK 36-11-51-000-040) and (Ref. AMM TASK 36-11-51-400-040).
B. After the subsequent flight, make sure that the fault does not continue.
1
-EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 275
--Feb 01/05R ---CES -
HP Bleed Valve of the Engine 2 Blocked in the Open Position
1. Possible Causes
_______________
-VALVE-HP BLEED (4000HA)
-
wiring
-
wiring between pin A/3 of the HP bleed valve and the ground terminal
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 36-11-51-000-040 Removal of the High Pressure Bleed Valve (4000HA) AMM 36-11-51-400-040 Installation of the High Pressure Bleed Valve (4000HA) ASM 36-11/02
3. Fault Confirmation
__________________
A. Test
(1) Not applicable
4. Fault Isolation
_______________
A. If the fault symptom is identified by the maintenance message:
HP BLEED-V 4000HA2
-make sure that the indication of the position of the HP bleed valve on the lower ECAM display unit is correct when you manually operate the valve shaft.
(1) If the indication does not agree with the position of the valve butterfly:
-do a check and repair the wiring from the HP bleed valve to the BMC2, pin A/1 to pin AA/14A and pin A/5 to pin AA/15A (Ref. ASM 36-11/02).
(a)
If the fault continues:
-do a check and repair the wiring between pin A/3 of the HP bleed valve and the ground terminal.
(b)
If the fault continues:
-replace the VALVE-HP BLEED (4000HA) (Ref. AMM TASK 36-11-51-000-040) and (Ref. AMM TASK 36-11-51-400-040).
B. After the subsequent flight, make sure that the fault does not continue.
1
-EFF : ALL
-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 276
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 PNEUMATIC(44)
