(2)  
AMM 24-11-11/401, Constant Speed Drive

 (3)  
AMM 24-11-21/401, Generator Drive Oil Cooler

 (4)  
AMM 71-11-02/201, Fan Cowl Panels

 C.
Access

 (1)  
Location Zones
 506 Engine 1 - Accessory Gearbox, 8 o'clock
 506 Engine 1 - Fan Case, 5 o'clock
 606 Engine 2 - Accessory Gearbox, 8 o'clock
 606 Engine 2 - Fan Case, 5 o'clock

 (2)  
Access Panels
 5746 Left Fan Cowl - Engine 1
 5846 Left Fan Cowl - Engine 2

 D.
Examine the Constant Speed Drive (Fig. 601).

 (1)  
Open the left fan cowl on the applicable engine (AMM 71-11-02/201).

 S 016-002
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. CONSTANT SPEED DRIVES ú

 24-11-11
 ú ú 02 Page 601 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
OIL LEVEL SIGHT GAGE
INTEGRAL OIL FILTER
SEE B MAGNETIC PLUG
CONSTANT SPEED DRIVE  SEE A LINE OIL FILTER 
HOUSING FILTER LINE OIL  INTEGRAL OIL FILTER COVER 
POP-OUT INDICATOR  POP-OUT INDICATOR 
A  B 
Generator Drive Inspection Points Figure 601 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. CONSTANT SPEED DRIVES ú

 24-11-11
 ú ú 02 Page 602 ú Jul 15/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 026-017
 WARNING:_______ DO NOT TOUCH THE OIL SYSTEM PARTS WHEN THEY ARE HOT.  THESE
 PARTS STAY HOTTER THAN THE OTHER ENGINE PARTS AFTER AN ENGINE
 SHUTDOWN.  OIL SYSTEM PARTS THAT ARE HOT CAN BURN YOU.
 DO NOT LET THE OIL TOUCH YOUR SKIN FOR A LONG TIME.  YOU CAN
 ABSORB POISONOUS MATERIALS FROM THE OIL THROUGH YOUR SKIN.  OIL
 ON YOUR SKIN CAN CAUSE DERMATITIS AFTER A LONG TIME.

 CAUTION:_______DO NOT REMOVE THE OUTER 3/4-INCH PLUG. THIS WILL CAUSE THE CSD OIL TO DRAIN.
 IMMEDIATELY REMOVE ALL OF THE OIL THAT FALLS ON THE ENGINE PARTS. OIL CAN CAUSE DAMAGE TO THE PAINT AND SOME RUBBER PARTS.
 (2)  Remove only the inner magnetic plug with a 9/16-inch or 14 mm wrench.
 NOTE: A check valve prevents oil leakage when you remove only the
____ inner magnetic plug.
 S 216-004
 (3)  Examine the metal particles that are on the magnetic plug (Fig. 602).
 (a)  If there is a large quantity of small metal particles, do as follows: 1) Use a brush and compressed air to remove all of the
 particles from the magnetic plug. 2) Install the magnetic plug and torque from 15 to 20 pound-inches.
 3)  Examine the magnetic plug again after the engine operates again. If a large quantity of metal particles is on the magnetic plug, do as follows: a) Do not clean the magnetic plug. Install the magnetic
 plug in the CSD. b) Replace the CSD (Ref 24-11-11/401). c) Replace the CSD oil cooler (AMM 24-11-21/401). d) Replace the CSD line oil filter (AMM 24-11-31/201). e) Replace all tubing for the CSD oil system.
 (b)  If there are bright metal chips or flakes on the magnetic plug, do as follows: 1) Do not clean the magnetic plug. Install the magnetic plug
 in the CSD. 2) Replace the CSD (AMM 24-11-11/401). 3) Replace the CSD oil cooler (AMM 24-11-21/401). 4) Replace the CSD line oil filter (AMM 24-11-31/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. CONSTANT SPEED DRIVES ú

 24-11-11
 ú ú 02 Page 603 ú Nov 15/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (c)  5) Replace all tubing for the CSD oil system.If there is a small quantity of small metal particles on the magnetic plug, the CSD is serviceable.
 (4)  S 166-010Use a brush and compressed air to remove all of the particles from the magnetic plug.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 電源 ELECTRICAL POWER(58)