D. Procedure
 S 014-001
 (1)  
Make sure the crossfeed manifold valve is closed.

 S 864-011

 (2)  
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  P6 Main Power Distribution Panel
 1) 6B5 FUEL SHUTOFF VALVE
 2) 6D3 SHUTOFF VALVE ENG 2
 3) 6D7 SHUTOFF VALVE ENG 1

 S 014-002
 (3)  Open the access door, No. 6212, to the shutoff valve for the engine fuel (left side) or the access door, No. 6512, (right side).
 NOTE: These access doors are immediately outboard of the
____
 engine.

 S 214-012
 (4)  
Make sure there is less than 5360 pounds of fuel in the applicable fuel tank.

 S 034-020

 (5)  
Remove the lockwire and disconnect the electrical plug from the shutoff valve.

 S 034-021

 (6)  
Disconnect the bonding jumper from the shutoff valve.

 S 494-022

 (7)  
Put an applicable container below the shutoff valve to catch the fuel.

 S 034-023

 (8)  
Remove the nuts and washers which attach the actuator assembly and the gate assembly.

 (9)  
Remove the clamp from the thermal anti-ice duct.

 S 434-008

 (10)
 Turn the duct to get sufficient clearance to permit the removal of the shutoff valve.

 S 424-007
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-11
 ALL  ú ú 02 Page 403 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 024-053
 (11) Carefully remove the actuator assembly and the gate assembly as a unit from the opening in the front spar.
 NOTE: If you are not scheduled to remove the port adapter
____ assembly, make sure you did not loosen the bolts that attach the port adapter assembly.
 S 024-055
 (12) To remove the actuator assembly (if necessary) from the gate assembly, do the steps that follow:
 CAUTION: MAKE SURE YOU HOLD THE ACTUATOR ASSEMBLY WHEN YOU REMOVE
_______ THE BOLTS. IF YOU DO NOT HOLD THE ACTUATOR ASSEMBLY, THE SPLINE SHAFT CAN BE DAMAGED.
 (a)  
Hold the actuator assembly and remove the mounting bolts (Fig. 401).

 (b)  
Carefully move the actuator assembly away from the gate assembly until the output shaft is clear of mating parts and lift the actuator assembly clear.

 TASK 28-22-11-404-006
 3. Shutoff Valve Actuator and Gate Assembly Installation (Fig. 401)
_____________________________________________________
 A. Equipment
 (1)  
Bonding Meter - Avtron T477W, Avtron Manufacturing Co.

 (2)  
Container - To hold residual fuel from fuel manifold

 B. Consumable Materials
 (1)  
D00057 - Grease - Airplane, High Temperature - MIL-G-3545

 (2)  
B00316 Cleaning Solvent - Aliphatic Naphtha TT-N-95

 C. References
 (1)  
SWPM 20-20-00, Standard Wiring Practices Manual

 (2)  
WDM 28-21-01

 D. Access
 (1)  
Location Zones
 305 Left Fuel Tank
 303 Left Wing Inboard Leading Edge
 405 Right Fuel Tank
 403 Right Wing Inboard Leading Edge

 (2)  
Access Panels
 6212 Slat Access Panel (left)
 6512 Slat Access Panel (right)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-11
 ALL  ú ú 01 Page 404 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 E. Procedure
 S 424-056
 (1)  To install the actuator assembly (if necessary) to the gate
 assembly, do the steps that follow:

 (a)  
Lightly apply a layer of grease to the splines of the output shaft.

 (b)  
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 2(105)