_______LEDGEND GREASE HERE APPLY MIL-G-27617 WING REAR SPAR B
Figure 201 Crossfeed Valve Installation
M25907
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-22-21
ALL ú ú 01 Page 202 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FUEL CROSSFEED VALVE - REMOVAL/INSTALLATION
___________________________________________
1. General_______
A. This procedure has these six tasks:
(1)
A task to remove the actuator assembly for the fuel crossfeed valve
(2)
A task to install the actuator assembly for the crossfeed valve
(3)
A task to remove the gate assembly for the fuel crossfeed valve
(4)
A task to install the gate assembly for the fuel crossfeed valve
(5)
A task to remove the port adapter assembly for the fuel crossfeed valve
(6)
A task to install the port adapter assembly for the fuel crossfeed valve.
B. The fuel crossfeed valve is installed on the rear spar of the right wing. The fuel crossfeed valve has these three primary assemblies:
(1)
The actuator assembly
(2)
The gate assembly
(3)
The port adapter assembly.
C. The actuator assembly is attached to the gate assembly with bolts. You can remove the actuator assembly with the gate assembly as an assembled unit. But it is not necessary to remove the gate assembly to remove the actuator assembly.
D. You must remove the actuator assembly and the gate assembly to remove the port adapter assembly. You must also defuel the No. 2 fuel tank to remove the port adapter assembly.
E. The No. 1 tank must contain less than 1000 pounds (454 kilograms) of fuel to remove the gate assembly. The No. 2 tank must also contain less than 1000 pounds (454 kilograms) to remove the gate assembly.
TASK 28-22-21-004-001
2. Crossfeed Valve Actuator Assembly Removal (Fig. 401)_________________________________________
A. Access
(1) Location Zone
405 Right Fuel Tank
B. Procedure
S 864-002
(1)
Open this circuit breaker and attach a DO-NOT-CLOSE tag:
(a) P6 Main Power Distribution Panel 1) CROSSFD VALVE (for the fuel crossfeed valve)
(2)
Disconnect the electrical plug from the crossfeed valve.
(3)
Disconnect the bonding jumper from the valve.
S 034-003
S 034-004
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-22-21
ALL ú ú 01 Page 401 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
REAR SPAR WING
ENGINE NO. 2
SEE B INDICATOR POSITION VALVE
SEE CROSSFEED VALVE A INBD VALVE CROSSFEED
A CROSSFEED VALVE
MOTOR
ASSEMBLY FOR THE ACTUATOR MOUNTING SCREWS
GATE SEAL ASSEMBLY ADAPTER PORT HOUSING VALVE RELIEF THERMAL INDICATOR POSITION VALVE GEAR TRAIN
SEAL
ARM ACTUATING
SEAL HOUSING WING REAR SPAR O-RING CARRIER SEAL B PORT ADAPTER ASSEMBLY MOUNTING BOLTS FOR THE GATE SLIDING ROLLER HOUSING NUTS THAT ATTACH THE GATE ASSEMBLY
Figure 401 Crossfeed Valve Installation
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-22-21
ALL ú ú 01 Page 402 ú Jul 15/91
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 2(122)
