(2)
Access Panels
6540 Refueling Station Access Door
C. Procedure
S 432-010
(1)
Install the sensor mounting bracket if you removed it.
S 422-011
(2)
Put the sensor on the inboard side of the sensor mounting bracket.
S 422-012
(3)
Install the sensor mounting screws and washers.
S 432-013
(4)
Connect the sensor hot wire to pin 11 of the fueling panel disconnect receptacle.
S 432-014
(5)
Connect the sensor ground wire to the ground terminal screw.
S 822-015
(6)
Use the non-magnetic feeler gage to make sure the clearance is correct between the actuator magnet and the sensor.
NOTE: The clearance must be 0.080 | 0.020 inch at all the positions
____ of the access door between the open and closed positions.
S 822-016
(7) Do the steps that follow to adjust the clearance if it is necessary.
(a)
Loosen the screws for the sensor mounting bracket.
(b)
Move the bracket to get the correct clearance.
(c)
Tighten the screws for the sensor mounting bracket.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-21-81
ALL ú ú 01 Page 203 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 862-029
(8) Close these circuit breakers and remove the DO-NOT-CLOSE tags:
(a) P6 Main Power Distribution Panel
1) EP GND FUELING
2) QTY
TASK 28-21-81-352-017
4. Repair the Fueling Power Control Switch Actuator (Fig. 201)________________________________________________
A. Consumable Materials
(1)
C00057 - Primer, Zinc Chromate TT-P-1757 Color Y.
(2)
Use one of these sealants (adhesives):
(a)
A00142 - BMS 5-44, Class B
(b)
A00247 - BMS 5-95
(3)
B00148 - Methyl Ethyl Ketone (MEK) or equivalent
B. Access
(1) Location Zone
402 Right Wing Outboard Leading Edge
C. Procedure
S 022-018
(1)
Remove the actuator bracket from the fueling station door.
S 162-019
(2)
Remove the remaining adhesive from the actuator magnet and the bracket.
S 112-020
(3)
Use solvent, Series 90 (AMM 20-30-90/201) to clean the faying surfaces of the magnet and the bracket.
(4)
Apply one layer of primer to the magnet and the bracket.
(5)
Apply adhesive to the faying surfaces.
S 352-023
(6)
Put the magnet on the bracket and push them lightly together.
S 372-021
S 352-022
NOTE:____Do not apply too much adhesive to the surfaces. Unwanted adhesive will come out of the space between the two surfaces when you push them together.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-21-81
ALL ú ú 01 Page 204 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(7) S 352-024Let the adhesive dry for the applicable cure time.
(8) S 422-025Install the actuator bracket on the fueling station door.
(9) S 822-026Make sure the clearance is correct between the actuator magnet and the sensor.
S 822-027
(10) Adjust the clearance if it is necessary. 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 2(60)
