S 865-019

 (3)  
Open these circuit breakers and attach DO-NOT CLOSE tags:

 (a)  
P6-11 Circuit Breaker Panel
 1) STBY HYD PUMP NORMAL

 (b)  
P6-12 Circuit Breaker Panel
 1) STBY HYD PUMP (ALT)

 S 865-020
 (4)  Put the ALTERNATE FLAPS arm switch to the ARM position.
 (a)  Make sure the STANDBY HYD LOW PRESSURE light, on the P5 panel, comes on.
 S 495-033
 (5)  Install the hydraulic test bench:
 (a)  
Disconnect the pressure hose of the standby pump at the disconnect half on the aft bulkhead.

 (b)  
Attach the pressure hose of the hydraulic test bench to the disconnect half on the aft bulkhead.

 (c)  
Attach the return hose for the hydraulic test bench to the return port of the hydraulic system B ground service.

 S 785-029
 (6)  Slowly increase the hydraulic pressure.
 (a)  Make sure the STANDBY HYD LOW PRESSURE light goes off between 1100 and 1600 psi.
 S 785-023
 (7)  Slowly decrease the pressure.
 (a)  Make sure the STANDBY HYD LOW PRESSURE light comes on at 1500 to 1000 psi.
 S 095-032
 (8)  Remove the hydraulic test bench:
 (a)  Remove the pressure hose of the hydraulic test bench from the disconnect half on the aft bulkhead.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-34-01
 ALL  ú ú 01 Page 504 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (b)  
Connect the pressure hose of the standby pump to the disconnect half on the aft bulkhead.

 (c)  
Disconnect the return hose of the hydraulic test bench from the hydraulic system B ground service module.

 S 865-026
 (9)  
Put the ALTERNATE FLAPS arm switch to the OFF position.

 S 435-027

 (10)
 Install a lockwire.

 S 865-028

 (11)
 Remove the DO-NOT CLOSE tags and close these circuit breakers:

 (a)  
P6-11 Circuit Circuit Breaker Panel
 1) STBY HYD PUMP NORMAL

 (b)  
P6-12 Circuit Breaker Panel
 1) STBY HYD PUMP (ALT)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-34-01
 ALL  ú ú 01 Page 505 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 HYDRAULIC SYSTEMS A AND B EDP LOW PRESSURE SWITCH -
___________________________________________________ REMOVAL/INSTALLATION
____________________
 1.  General_______
 A.  There are two tasks in this procedure. There is a task for the removal and a task for the installation of the hydraulic systems A and B EDP low pressure switch.
 B.  There is a low pressure switch for each engine driven pump on the systems A and B pressure modules.
 TASK 29-34-11-004-001
 2.  Hydraulic Systems A and B EDP Low Pressure Switch Removal (Fig. 401)_________________________________________________________
 A.  References
 (1)  29-15-00/201, Hydraulic Systems A, B and Standby
 B.  Access
 (1)  Location Zone
 101 Control Cabin, LH
 102 Control Cabin, RH
 216 Main Wheel Well, LH
 217 Main Wheel Well, RH

 C.  Procedure
 S 864-002
 (1)  
Remove power from the applicable hydraulic system
 (Ref 29-15-00/201).

 S 864-003

 (2)  
Open the applicable circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P6-2 Circuit Breaker Panel 1) HYD SYSTEM ELEC HYD PUMP CONT SYS A 2) HYD SYSTEM ELEC HYD PUMP CONT SYS B

 (b)  
P6-3 Circuit Breaker Panel 1) INDICATOR MASTER DIM BUS SECT 5 (system B) 2) INDICATOR MASTER DIM BUS SECT 6 (system A)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 液壓 HYDRAULIC POWER(166)