(2)  
D00153 Hydraulic Fluid - BMS 3-11

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-09-11
 ALL  ú ú 02 Page 204 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 B.  Access
 (1)  Location Zones
 217 Right Main Wheel Well

 C.  Procedure
 S 432-014
 (1)  Install these parts in the pressurization module if they are not installed:
 (a)  
The orifice assembly: 1) Lubricate the threads, the O-rings, and the backup ring with assembly lube or hydraulic fluid. 2) Put the O-rings and the backup ring on the orifice assembly.

 3)  Install the orifice assembly on the pressurization module but do not tighten it.

 (b)  
The plug in the test port: 1) Lubricate the threads, and the O-ring with assembly lube or

 hydraulic fluid. 2) Install the O-ring on the test plug. 3) Install the test plug in the pressurization module.

 (c)  
The reducers in the pneumatic supply port: 1) Lubricate the threads, and the O-ring with assembly lube or

 hydraulic fluid. 2) Install the O-rings on the reducers.
 NOTE: Use new O-ring for reducers with MOD "1" marking on
____ the identification plate.
 3) Install the reducers in the pressurization module.
 S 422-015
 (2)  
Attach the pressurization module to the airplane with the mounting bolts, washers, and nuts.

 (3)  
Remove the caps from the tubes and the pneumatic supply lines.

 S 422-054
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-09-11
 ALL  ú ú 01 Page 205 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 422-055
 (4)  For pressurization modules without the tee assemblies connect the tube to the orifice assembly:
 (a)  
Adjust the orifice assembly until you can connect the tube.

 (b)  
Tighten the orfice assembly.

 S 432-016
 (5)  For pressurization modules with tees connect the tees to the orifice assembly but do not tighten them.
 (a)  
Align the tees and the orifice assembly until the tubes are not stressed.

 (b)  
Tighten the tees and the orifice assembly.

 S 422-056
 (6)  
Connect the pneumatic supply lines to the pressurization module.

 S 862-017

 (7)  
Remove the DO-NOT-USE tag from the connector for the ground pneumatic air.

 S 792-018

 (8)  
Do the leak check for the pressurization module.

 S 862-019

 (9)  
Remove the source of pressure from the pneumatic system.

 TASK 29-09-11-002-020
 5.  Pressurization Module Filter Removal (Fig. 201)____________________________________
 A. Consumable Materials
 (1)  
B01000 Solvent - General Cleaning of Metal (Series 80) (AMM 20-30-80 or SOPM 20-30-80)

 (2)  
B01003 Solvent - General Cleaning of Composites (Series 83) (AMM 20-30-83 or SOPM 20-30-83)

 B. Access
 (1)  Location Zones
 217 Right Main Wheel Well

 C. Procedure
 S 842-021
 (1)  
Do the steps to prepare for maintenance of the pressurization module.

 S 142-025

 (2)  
Remove the sealant that is around the filter cap with a wooden or plastic scraper.

 S 022-026

 (3)  
Remove the filter cap, the filter element, and the sleeve from the pressurization module.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-09-11
 ALL  ú ú 01 Page 206 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 液壓 HYDRAULIC POWER(51)