EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-15-27
ALL ú ú 02 Page 406 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
STANDBY HYDRAULIC SYSTEM ELECTRIC MOTOR-DRIVEN PUMP (EMDP) -
____________________________________________________________ REMOVAL/INSTALLATION
____________________
1. General_______
A. If you replace the standby hydraulic pump because of a mechanical malfunction, do the following:
B. Remove and clean the filter bowls.
C. Replace the filter elements in the pressure and the case drain filters.
TASK 29-15-31-004-031
2. Standby Hydraulic System Electric Motor-Driven Pump (EMDP) Removal__________________________________________________________________
A. References
(1)
12-40-00/201, Cleaning and Washing
(2)
29-09-00/201, Hydraulic Reservoir Pressurization System
B. Access
(1) Location Zone
216,217 Main Wheel Well
C. Prepare for the Removal
S 864-001
(1)
Remove the pressure from the standby reservoir (Ref 29-09-00/201).
S 864-002
(2)
Open the applicable circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P6-11 Circuit Breaker Panel
1) STBY HYD PUMP NORMAL
2) ELEC HYD PUMP SYS B
(b)
P6-12 Circuit Breaker Panel
1) STBY HYD PUMP (ALT)
2) ELEC HYD PUMP SYS A
S 034-042
CAUTION: MAKE SURE THAT YOU PULL DOWN ON THE KNURLED RING OF THE
_______ SELF-SEAL DISCONNECT BEFORE YOU TURN IT FOR REMOVAL. IF YOU DO NOT DO THIS, TOO MUCH TORQUE WILL BE NECESSARY TO TURN THE RING WHICH WILL DAMAGE THE SELF-SEAL DISCONNECT.
(3) Disconnect the pump supply line at the quick-disconnect on the standby reservoir.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-15-31
ALL ú ú 01 Page 401 ú Jul 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
STANDBY
HYDRAULIC
SYSTEM STANDBY
PRESSURE
SEE A MODULE STANDBY
RESERVOIR
QUICK-DISCONNECT
KEEL BEAM
STANDBY EMDP
FWD
SEE B
STANDBY HYDRAULIC SYSTEM
A
ELECTRIC
MOTOR ELECTRICAL CONNECTOR
SUPPLY LINE
PRESSURE LINE
FASTENERS
(EXAMPLE)
CASE DRAIN LINE PUMP
SHAFT SEAL DRAIN
(BOTTOM OF PUMP)
STANDBY EMDP B Standby Hydraulic System EMDP Removal/Installation Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-15-31
ALL ú ú 01 Page 402 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
D. Remove the Hydraulic Pump Assembly
S 034-034
(1)
Disconnect the electrical connector for the hydraulic pump.
S 034-035
(2)
Disconnect the hydraulic lines from the pump.
S 864-036
(3)
Put a container below the pump to catch hydraulic fluid.
S 164-037
(4)
Clean hydraulic fluid if it gets on the airplane (Ref 12-40-00/201).
S 434-038
(5)
Install the protective caps.
S 034-039
(6)
Remove the bolts.
S 024-040
(7)
Remove the pump assembly.
TASK 29-15-31-404-032
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 液壓 HYDRAULIC POWER(99)
