(b)
Connect one end of the cable assembly to the standby EMDP (Fig. 606).
(c)
Connect the other end of the cable assembly to the electrical connector (Fig. 606).
CAUTION:_______PUT THE AMMETER IN THE SHORT CIRCUIT POSITION. THE CURRENT TO START THE EMDP IS APPROXIMATELY 180 AMPS. THIS WILL CAUSE DAMAGE TO THE AMMETER IF IT IS IN THE CIRCUIT.
(d)
Put the switch on the ammeter in the short circuit position.
S 486-178
(4) To use the flowmeter procedure, do these steps:
(a)
Open these circuit breakers:
1) P6-11 panel
a) STBY HYD PUMP NORMAL
2) P6-12 panel
a) STBY HYD PUMP ALTERNATE
(b)
Install the flow meter at the outlet of the standby EMDP.
S 486-179
(5) To use the amp-clamp and multimeter procedure, do these steps:
(a) Get access to the applicable circuit breaker:
NOTE: You can also use one of the three load wires connected
____ to standby hydraulic pump relay, R68, to put the amp-clamp adapter around.
1) P6-11 panel
a) C847 STBY HYD PUMP NORMAL (use this circuit breaker if the No. 1 GEN BUS has power, or if the No. 1 and the No. 2 GEN BUS have power)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-00-00
ALL ú ú 01 Page 667 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
2) P6-12 panel a) C848 STBY HYD PUMP ALTERNATE (use this circuit breaker
if only the No. 2 GEN BUS has power)
CAUTION:_______ MAKE SURE THE AMP-CLAMP DOES NOT TOUCH THE CIRCUIT BREAKER
TERMINALS. IT CAN CAUSE A SHORT CIRCUIT.
(b)
Put the amp-clamp adapter around one of the three wires connected to the load side of the circuit breaker.
(c)
Connect the multimeter to the amp-clamp adapter.
S 866-180
(6) Close these circuit breakers:
(a)
P6-11 panel 1) STBY HYD PUMP NORMAL
(b)
P6-12 panel 1) STBY HYD PUMP ALTERNATE
S 866-181
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE RUDDER,
_______ LEADING EDGE SLATS, AND THRUST REVERSERS. THEY CAN MOVE QUICKLY WHEN YOU SUPPLY STANDBY HYDRAULIC POWER.
(7)
Put the arm switch for the ALTERNATE FLAPS in the ARM position (on the P5 panel).
S 866-182
(8)
Remove hydraulic power from the A and B hydraulic systems (AMM 29-15-00/201).
S 866-186
(9)
Put the FLT CONTROL A switch in the STDBY RUD position.
S 846-189
(10)
Operate the rudder until the temperature of the hydraulic fluid is more than 70°F.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-00-00
ALL ú ú 01 Page 668 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 796-188
(11) Do these steps to make sure the pressure relief valve in the standby pressure module is serviceable:
(a)
Make sure the standby pressure module does not make a hissing noise.
(b)
Make sure the return line from the standby pressure module is not hot.
(c)
If you hear a hissing noise or the return line is hot, replace the pressure relief valve (AMM 29-15-81/201).
F. Procedure
S 866-190
(1)
Put the FLT CONTROL A switch in the A ON position.
S 796-193
(2)
Put the FLT CONTROL B switch in the B ON position.
(a) Read the amperage and write it for step 1 of Figure 609.
S 796-194
(3) Put the FLT CONTROL A switch in the STDBY RUD position.
(a)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 液壓 HYDRAULIC POWER(41)
