(2)
You must find the changes in the flow of hydraulic fluid (during different conditions of operation) to find the internal leakage rate for each part. There are three procedures to measure the flow: the ammeter procedure, the flowmeter procedure, and the amp-clamp and multimeter procedure.
(a)
To use the ammeter procedure, you connect an ammeter in series with one phase of the motor on the electric motor-driven pump (EMDP). To find the flow you measure the current, subtract the applicable system basic current, and use Figure 603 to change it to a flow.
(b)
To use the flowmeter procedure, you install a flowmeter on a hydraulic service cart and read the flow from it.
(c)
To use the amp-clamp and multimeter procedure, you put the amp-clamp adapter around one of the wires connected to a relay for the EMDP. You then read the current on the multimeter (that is connected to the amp-clamp adapter) subtract the applicable system basic current, and use Figure 603 to get the flow. One person can do this procedure from the Control Cabin.
(3)
When you read the ammeter, make a record of the value to the nearest
0.1 ampere. Use Figure 603 to change current to flow.
(4)
If you use the flowmeter procedure, make a record of the value to the nearest 100 cc/minute.
B. Special Tools and Equipment
(1) Test Set - SP177/SP300 Autopilot Elevator/Rudder/Aileron and Spoiler
-F80217-103
C. Access
(1) Location Zones
101/102 Control Cabin
216/217 Main Wheel Wells
D. Procedure
S 846-134
(1)
Do the Prepare for an Internal Leak Check procedure.
S 866-135
(2)
Close the No. 1 through No. 6 isolation valves (in the tail compartment) (Fig 604).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-00-00
ALL ú ú 06 Page 642 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 866-137
(3)
AIRPLANES WITH ISOLATION VALVES FOR THE LANDING GEAR; Close them (Fig. 604).
S 976-258
(4)
If you use the ammeter or amp-clamp method, do this step to determine the system B basic current:
NOTE: This is the system B basic current, and must be subtracted
____ from all other system B amperage readings before you use Fig. 603 to find the flow.
(a) Read the amperage and write it here:
Amperage _______________ (System B Basic Current)
S 976-281
(5) If you use the ammeter or amp-clamp method, do these steps to determine the system A basic current:
NOTE: This is the system A basic current, and must be subtracted
____ from all other system A amperage readings before you use Fig. 603 to find the flow.
(a)
Remove hydraulic power from hydraulic system B
(AMM 29-15-00/201).
(b)
Supply hydraulic power to hydraulic system A with the electric motor driven pump (AMM 29-15-00/201).
(c)
Make sure that the pressure in system A is a minimum of 2800 psi.
(d)
Read the amperage and write it here:
Amperage _______________ (System A Basic Current)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-00-00
ALL ú ú 01 Page 643 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 液壓 HYDRAULIC POWER(30)
