2)  Load Control Center - Left, P18-0 a) STABILIZER TRIM
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH A KORRY 432 SERIES ú

 33-11-80
 STABILIZER TRIM WARNING LIGHT  ú ú 01 Page 201 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500MAINTENANCE MANUAL
BASE ASSEMBLY TO PANEL MOUNTING BRACKET (2 LOCATIONS)
BASE
CAP ASSEMBLY ASSEMBLY
RETAINING
HOLE FOR ELEMENTS
CAP ASSEMBLY LOCKING PIN
BASE ASSEMBLY IDENTIFICATION TO PROVIDE LOCKING PIN LATCH
CAP ASSEMBLY LOCKING PIN LENS CAP MUST BE FULLY EXTENDED CAP ASSEMBLY
SEEA B (1.20 INCHES MIN) PRIOR TO INSTALLATION
INDICATOR LIGHT IN RELAMPING POSITION
BASE SPRINGACTUATOR
LOCKING 
ASSEMBLY  LOCKING PIN  PIN  LOCKING PIN  MOUNTING 
ACCESS HOLE  LATCHING DETENT  BRACKET 
CAP  FASTENER 
ASSEMBLY  (2 LOCATIONS) 

REASSEMBLED INDICATOR LIGHT  MOUNTING BRACKET INDICATOR LIGHT 
(2 LOCATIONS) 
(RETRACTED) LOCKING PIN  (COMPRESSED) ACTUATOR SPRING  CAP SHELL  LAMP HOLDER 
LAMP 
(4 LOCATIONS) 

SHAFT LAMP ACTUATOR ACTUATOR(4 LOCATIONS)SHAFT SHAFT
LOCKING PINCAP SHELL LAMP HOLDER
(EXTENDED) CAP ASSEMBLY IN EXTENDED POSITION CAP ASSEMBLY IN COLLAPSED POSITION
A B
Stabilizer Trim Warning Light - Lamp Replacement Figure 201
H83490
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH A KORRY 432 SERIES ú

 33-11-80
 STABILIZER TRIM WARNING LIGHT  ú ú 01 Page 202 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 962-008
 (2)  Replace The Stabilizer Trim Warning Light Lamp(s)
 (a)  Grasp the cap assembly and pull directly out to retract the cap assembly locking pins. Continue to pull the cap assembly until it is free from the base assembly.
 NOTE: The cap assembly will remain captive to the base
____
 assembly by two retaining elements.

 (b)  
Replace the faulty lamp(s).

 (c)  
Check that the cap assembly is in the extended position (Fig. 201). If in a collapsed position, do these two steps: 1) Grasp the cap shell and the lamp holder. 2) Draw apart the cap shell from the lamp holder until the

 locking pins are retracted.
 NOTE: In the collapsed position, locking pins are
____ extended and cannot lock the cap assembly into the base assembly. Therefore, the shaft will not actuate the switches and the lamps will fail to contact the energized pins in the mounting base.
 (d)  Insert the cap assembly into the mounting base. Push with a firm continuous action until the cap assembly bottoms out in the base assembly. The cap assembly should collapse and the locking pins should engage the base assembly.
 NOTE: Hesitation to insert the cap assembly into the base
____ assembly may cause the cap to prematurely release and cause the unit to jam.
 S 862-009
 (3)  Remove the DO-NOT-CLOSE tags and close these circuit breakers:
 (a)  
Load Control Center, P6-3
 1) MASTER DIM SECT 2

 (b)  
Load Control Center - Left, P18-0
 1) STABILIZER TRIM

 S 712-010
 (4)  
Momentarily press and hold the master dim and test LIGHTS switch (P1-3) to the TEST position and make sure the lamps come on.

 (5)  
Remove electrical power if no longer necessary (AMM 24-22-00/201).

 S 862-011
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH A KORRY 432 SERIES ú

 33-11-80
 STABILIZER TRIM WARNING LIGHT  ú ú 01 Page 203 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燈 LIGHTS(11)