(b)
Release the latches behind the sign assembly.
(c)
Remove the rear housing.
(d)
Carefully replace the lamp through the rear of the sign assembly.
(e)
Install the rear housing and close the latches.
(f)
Close the PSU (AMM 25-23-61/201).
S 712-050
(4) Do a test of the sign.
(a)
Remove each DO-NOT-OPERATE or DO-NOT-CLOSE tag.
1) Close each circuit breaker that was opened.
(b)
Set the NO SMOKING switch to the on position.
(c)
Set the FASTEN BELTS switch to the on position.
1) Make sure the new lamp comes on correctly.
(d)
Set the NO SMOKING switch to the usual position.
(e)
Set the FASTEN BELTS switch to the usual position.
(f)
Remove electrical power if it is not necessary
(AMM 24-22-00/201).
SLOT 1
"NO SMOKING"/
"FASTEN SEAT BELT" SIGN
(EXAMPLE)
"NO SMOKING"/"FASTEN SEAT BELT" SIGN WITH A SLOT.
Passenger Signs - Lamp Replacement
Figure 201
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
33-24-00
ALL ú ú 01 Page 204 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E01266
A
737-300/400/500MAINTENANCE MANUAL
TASK 33-24-00-702-048
4. Passenger Sign Operational Test_______________________________
A. References
(1)
AMM 24-22-00/201, Manual Control
(2)
AMM 29-15-00/201, Hydraulic Systems A, B, and Standby
(3)
AMM 32-00-01/201, Ground Lock Assemblies
(4)
SSM 33-25-00 thru SSM 33-25-99
(5)
WDM 33-25-11 thru WDM 33-25-99
B. Access
(1) Location Zone
100 Upper Half of Fuselage
C. Procedure
S 862-059
(1)
Supply electrical power (AMM 24-22-00/201).
S 712-054
(2)
Do a test of the Passenger Signs:
(a)
Set the NO SMOKING and the FASTEN BELT switches on the overhead panel, P5, to ON. 1) Make sure that these passenger signs are on:
a) NO SMOKING b) FASTEN SEAT BELT c) RETURN TO SEAT
(b)
Set the NO SMOKING and the FASTEN BELT switches to OFF.
1) Make sure the passenger signs are off.
WARNING: MAKE SURE THE GROUND LOCKS ARE INSTALLED ON ALL THE
_______ LANDING GEAR BEFORE YOU MOVE THE CONTROL LEVER. WITHOUT THE GROUND LOCKS, THE LANDING GEAR CAN RETRACT AND CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(c) Make sure the ground locks are installed on the nose and main landing gear (AMM 32-00-01/201).
WARNING: KEEP PERSONS AND EQUIPMENT CLEAR OF THE FLIGHT CONTROL
_______ SURFACES, THE THRUST REVERSERS, AND THE LANDING GEAR. THESE COMPONENTS CAN MOVE SUDDENLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(d)
Supply hydraulic power (AMM 29-15-00/201).
(e)
Move the flap control lever to the UP position.
(f)
Move the landing gear lever to the off position.
(g)
Set the NO SMOKING and the FASTEN BELT switches to AUTO. 1) Make sure that all the passenger signs are off.
(h)
Move the flap control lever to POSITION 2.
1) Make sure that all the FASTEN SEAT BELT and the RETURN TO SEAT signs are on.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
33-24-00
ALL ú ú 01 Page 205 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燈 LIGHTS(39)
