EQUIPMENT.
(2)
Do this task: "Leading Edge Flap and Slat Locks Removal" (Ref 27-81-00/201).
S 862-008
(3)
Remove the electrical power if it is not necessary (Ref 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
33-42-41
ALL ú ú 01 Page 205 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
RUNWAY TURNOFF LIGHTS - ADJUSTMENT/TEST
_______________________________________
1. General_______
A. This procedure has these tasks:
(1)
Runway Turnoff Light - Adjustment with a Light Aligner
(2)
Runway Turnoff Light - Adjustment with a Target
B. Each runway turnoff light is adjacent to a inboard landing light. The two lights are behind one lens.
C. The runway turnoff lights are in a fuel vapor area. Each lamp, electrical connection, and lens has a seal to stop all fuel fumes and water.
D. The ground must be level below and in front of the airplane.
TASK 33-42-41-825-001
2. Runway Turnoff Light - Adjustment with a Light Aligner (Fig. 501 and 502)______________________________________________________
A. Equipment
(1) Light Aligner - LA-87,
J. C. Air, 400 Industrial Parkway,
Industrial Airport, Kansas City, Kansas 66031, U.S.A.
B. References
(1)
AMM 08-10-00/201, Leveling
(2)
AMM 24-22-00/201, Manual Control
(3)
AMM 27-81-00/201, Leading Edge Flap and Slat Locks Installation
(4)
AMM 33-42-21/401, Inboard Landing and Runway Turnoff Light Lens Assembly (Cover) - Removal/Installation
C. Access
(1) Location Zone 303 Left Wing Inboard Leading Edge Including Slats 403 Right Wing Inboard Leading Edge Including Slats
D. Procedure
S 865-029
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE LEADING EDGE FLAP AND SLAT LOCKS CORRECTLY. THE LEADING EDGE FLAPS AND SLATS CAN MOVE QUICKLY IF YOU DO NOT INSTALL THE LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1)
Do this task: "Leading Edge Flap and Slat Locks Installation" (AMM 27-81-00/201).
S 035-008
(2)
Remove the lens of the inboard landing and runway turnoff lights (AMM 33-42-21/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
33-42-41
ALL ú ú 01 Page 501 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(3) S 865-015Make sure the airplane and the test area are on level ground.
(4) S 865-008Make sure the airplane is approximately level (AMM 08-10-00/201).
(5) S 945-004Set the light aligner in its position (Fig. 502). (a) Measure the height of the light from the ground. (b) Use the height of the light to adjust the height of the light aligner (Fig. 502).
(6) S 865-005Supply electrical power (AMM 24-22-00/201).
(7) S 825-006Adjust the light.
CAUTION:_______ DO NOT MAKE THE LIGHTS COME ON FOR MORE THAN FIVE MINUTES. AFTER YOU MAKE THE LIGHTS COME ON, MAKE THE LIGHTS GO OFF FOR AN EQUAL TIME. BECAUSE OF THE HEAT, THE CONTINUED OPERATION OF THE LIGHTS CAN DECREASE THE LIFE OF THE LAMPS.
(a) (b) At the overhead panel, P5, set the switch for the runway turnoff light to the on position.Turn the adjustment screws of the light until the indicators on the light aligner change colors from yellow to black.
NOTE:____ The indicator in the center of the light aligner will stay yellow. All the other indicators must become black at the same time.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燈 LIGHTS(69)
