C. Procedure
S 862-005
(1) Open this circuit breaker and attach a DO-NOT-CLOSE tag:
(a) P18-3 Load Control Center - Left
1) NOSE GEAR TAXI
S 492-006
WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(2)
Make sure the ground locks are installed in all landing gear (AMM 32-00-01/201).
S 022-002
(3)
Remove the lamp.
(a)
Remove the retainer screws and the retainer.
(b)
Remove the lamp from the housing.
(c)
Disconnect the electrical wires from the terminals of the lamp.
S 422-003
(4) Install the new lamp.
(a)
Clean the terminals of the lamp and the ends of the electrical wires to remove all dirt and corrosion.
(b)
Connect the electrical wires to the terminals of the lamp.
NOTE: Tighten the screws until the lockwashers are fully
____
compressed.
(c) Put the lamp in the housing.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
33-42-51
ALL ú ú 01 Page 201 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500
MAINTENANCE MANUAL
SEE A NOSE GEAR TAXI LIGHT
AFT GASKET HOUSING
WIRES ELECTRICAL
LAMP LAMP SCREW TERMINALS
GASKET FORWARD RETAINER
(4 LOCATIONS) SCREW RETAINER
NOSE GEAR TAXI LIGHT
A
Nose Gear Taxi Light Figure 201
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
33-42-51
ALL ú ú 01 Page 202 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
CAUTION: HOLD THE LAMP IN THE CORRECT POSITION WHILE YOU INSTALL
_______ THE RETAINER. IF THE LAMP IS IN THE INCORRECT POSITION, THE INSTALLATION OF THE RETAINER CAN BREAK THE LAMP.
(d) Hold the lamp and install the retainer with the screws.
S 722-004
(5) Do a test of the nose gear taxi light.
(a)
Supply electrical power (AMM 24-22-00/201).
(b)
Remove the DO-NOT-CLOSE tag and close this circuit breaker:
1) P18-3 Load Control Center - Left
a) NOSE GEAR TAXI
(c)
On the pilot's overhead panel, P5,
set the TAXI switch to the ON position.
1) Make sure the light comes on.
(d)
Set the TAXI switch to the OFF position.
1) Make sure the light goes off.
(e)
Remove the electrical power if it is not necessary
(AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
33-42-51
ALL ú ú 02 Page 203 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
NOSE GEAR TAXI LIGHT - WIRING HARNESS REMOVAL/INSTALLATION
__________________________________________________________
1. General
_______
A. This procedure contains theses tasks for the nose gear taxi light (referred to as the light):
(1)
Wiring Harness - Removal
(2)
Wiring Harness - Installation
TASK 33-42-51-004-011
2. Wiring Harness - Removal
________________________
A. References
(1)
SSM 33-40-01
(2)
WDM 33-45-01
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燈 LIGHTS(72)
