曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 2) FMCS XFER
 S 862-107
 (4) Remove electrical power if it not necessary (AMM 24-22-00/201).
 J.  AIRPLANES WITH DUAL FMC;
 ú  FMC Software Crossload
 S 862-194
 (1) Do these steps to do the crossload.
 ú  (a) Make sure the OP PROGRAM CROSSLOAD or DATABASE CROSSLOAD page
 ú  is shown on the CDUs.
 NOTE: If not already shown, the Crossload pages are accessed____
 from the DUAL FMC BITE INDEX page, when you push the LSK
 adjacent to CROSSLOAD. If there is no mismatch between
 the op programs, the DATABASE CROSSLOAD page will be
 shown. If there are no database mismatches the DATABASE
 CROSSLOAD page will be empty.
 (b) Push the LSK adjacent to the FMC from which you will crossload
 the op program or database.
 NOTE: If the target FMC is the primary FMC, the CDU will show____
 a display to set the source select switch.
 (c) Make sure the CDUs show CROSSLOAD XXXXX TO YYYYY, where XXXXX
 is the source (primary) FMC and YYYYY is the secondary FMC.
 (d) Push the EXEC key.
 (e) Make sure CROSSLOAD COMPLETE is shown on the CDUs in 2 minutes
 or less.
 (f) If a different mismatch is found, NEXT MISMATCH will be shown
 on the CDUs.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú

 34-62-01

 ú ú 07.1 Page 208 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

Portable Data Loader (Diskette)
Figure 202 (Sheet 1)

C95305
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú

 34-62-01

 ú  ú
 ú  ú  07.101  Page 209
 ú  ú  Jul 12/02 

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

LOAD IN PROGRESS
LOAD COMPLETE
LOAD FAILURE
EXAMPLE OF FAILURE MESSAGES

CDU DISPLAY - DATA LOADING

Portable Data Loader
Figure 202 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú

 34-62-01

 ú  ú
 ú ú  ú 06.101 ú BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.  Page 210Jul 12/02 

 3.
ú ú ú ú ú ú
ú
ú
A
737-300/400/500MAINTENANCE MANUAL
 (g) Do the crossload again until NEXT MISMATCH is not shown.
 NOTE: If the ANALOG DISCRETES page is shown, the program pins
____ on one of the FMCs must be changed.
 (h)  If NEXT MISMATCH is not shown, push the LSK adjacent to INDEX to get out of the crossload.
 TASK 34-62-01-402-230Performance (Perf) Factors Modification Procedure
__________________________________________________
 A. General
(1)  Performance factors go to their default values when an operationalprogram (OPS) is loaded into the FMC. If different values aredesired they must be put in manually. The manual values are resetto the default values at flight completion or FMC power-up. If aperformance defaults data base is loaded into the FMC, this inhibitsvalues from being put in manually.
 B. References
 (1)  AMM 24-22-00/201, Electrical Power
 C. Access
 (1)  Location Zones
 101 Control Cabin, Left
 102 Control Cabin, Right

 D. Procedure
 S 472-235
 (1)  Do these steps to modify the perf factors:
 (a)  
Push the INIT REF mode key on the CDU.

 (b)  
Push the LSK adjacent to MAINT.

(c)  
Push the LSK adjacent to FMC LEFT.

 (d)  
Push the LSK adjacent to PERF FACTR.

　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 5(94)