72-56-00
 ALL  ú ú C01 Page 821 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
5) Loosen the stud. 6) Tighten the stud again to a torque of 490 to 530 pound-inches (55-60 Newton meters) (AMM 70-20-02/201).
 S 438-070-C00
 (4)  Install the rear cover on the turbine frame:
 (a)  
Use the studs as locators to put the rear cover in its correct position.

 (b)  
Make sure that the offset hole of the cover and the offset hole in the turbine frame align.

 NOTE: The offset hole locations are identified by an
____ indentation on the rear face of the cover and on the inner diameter of the turbine frame.
 (c)  
Apply a thin layer of graphite grease to the threads of the bolts that hold the rear cover. 1) Install the bolts.

 (d)  
Tighten the bolts to a torque of 85 to 90 pound-inch (9.5 to

 10.5 Nm).
 S 418-071-C00
 (5)  Install the flange assembly:
 CAUTION: BE CAREFUL WHEN YOU HANDLE THE GASKET SEAL AND THE FLANGE.
_______ IF YOU DO NOT USE PROPER CARE, YOU CAN CAUSE DAMAGE TO THE EQUIPMENT.
 (a)  
Install a new gasket seal on the forward flange of the flange assembly.

 (b)  
Apply a thin layer of graphite grease to the threads of the bolts that hold the flange assembly.

 (c)  
Use the bolts to install the flange assembly to the turbine frame.

 (d)  
Tighten the bolts to a torque of 85 to 90 pound-inch (9.5 to

 10.5 Nm).
 S 038-072-C00
 (6)  Install the flame arrestor on the flange assembly:
 (a)  
Apply a thin layer of graphite grease to the threads of the bolts that hold the flame arrestor.

 (b)  
Use the bolts to install the flame arrestor on the flange assembly.

 (c)  
Tighten the bolts to a torque of 100 to 115 pound-inch (11 to 13 Nm).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-56-00
 ALL  ú ú C02 Page 822 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 418-063-C00
 (7)  
Do this task: Install the Turbine Exhaust Plug
 (AMM 78-11-02/401).

 S 418-064-C00

 (8)  
Do this task: Install the Turbine Exhaust Sleeve
 (AMM 78-11-01/401).

 S 418-078-C00
 WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 TO CLOSE THE THRUST
_______ REVERSER. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
 (9)
Do this task: Close the Thrust Reverser (AMM 78-31-00/201).

 S 418-056-C00

 (10)
 Do this task: Close the Fan Cowl Panels (AMM 71-11-02/201).

 TASK 72-56-00-308-035-C00
 5. Midstream Fairing Repair with Patches
_____________________________________
 A. Equipment
 (1)  Drill
 B. Consumable Materials
 (1)  Grease
 C. Parts
 (1)  Cherry Lock rivets
 CR2663-5-3, or NAS1398C5-3

 D. Access
 (1)  Location Zones
 502/602 Left Fan Cowl Panels
 503/603 Right Fan Cowl Panels
 504/604 Left Thrust Reversers
 505/605 Right Thrust Reversers
 506 Engine No. 1 - Turbine Frame
 606 Engine No. 2 - Turbine Frame

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-56-00
 ALL  ú ú C02 Page 823 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 ENGINE 發動機 2(107)