72-33-00
 ALL  ú ú C02 Page 809 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 958-057-C00
 (6)  Apply heat-resistant tape (CP2306) to these areas:
 (a)  
The acoustical panels adjacent to the repaired area of the abradable liner for protection against heat.

 (b)  
The surfaces of all the acoustical panels between the 4:00 and

 8:00 o'clock locations (aft looking forward).
 NOTE: This will prevent the possible plugging of the
____ acoustical panel perforations with abradable dust caused by the hand sanding of the liner patch.
 S 038-058-C00
 (7)  On the forward and mid acoustical panels, locate the acoustical panels attachment screws you want to remove to attach the clamps with the slave bolts (Fig. 803).
 (a) Remove the screws, but keep the panels in their position.
 G. Patch Repair of the Abradable Shroud
 S 348-059-C00
 (1)  Make a mark around the area of the shroud you want to repair.
 S 348-112-C00
 CAUTION: MAKE SURE YOU DO NOT DAMAGE THE FAN CASE WITH THE CUTTING TOOL
_______ WHEN REMOVE THE ABRADABLE MATERIAL. DAMAGE TO EQUIPMENT CAN OCCUR.
 (2)  Remove the abradable material from this area, down to the fan case parent metal.
 (a)  Use a sharp cutting tool.
 S 348-060-C00
 (3)  
Make the surface of the case where you want to apply the patch rough.

 (a)  Use a 80 or 120 grade abrasive cloth (CP2239) and sand in a criss-cross pattern to get a good surface preparation.

 (4)  
Use an air source to clean the area.

 S 148-061-C00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-33-00
 ALL  ú ú C01 Page 810 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEE  A 
THERMALLY-
CONTROLLED 
ELECTRICAL 
SUPPLY 
PRESSURE 
RELIEF 
VALVE 
RELEASE FILM  AIR SUPPLY 
VALVE 
HEATING  PRESSURE 
BLANKET  GAGE
CLAMP AND BOLT  A 
(5 LOCATIONS) 
PRESSURE 
PAD 
HEAT 
RESISTANT  A 
TAPE 
REPAIR 
PATCH 
24 INCHES 
(600 mm) 
FAN 
FWD  CASE 

____ALL ENGINE COMPONENTS EXCEPTNOTE:
A
FAN CASE REMOVED FOR CLARITY.  S-M56-MM-03046-00-B
Patch Repair of the Abradable Shroud
Figure 803 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-33-00
 ALL  ú ú C02 Page 811 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E63092
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
AIR SUPPLY PRESSURE GAGE

CLAMP
A-A  NUT (2 LOCATIONS)
. INFLATEABLE JACKET - APPROPRIATE SHAPE/SIZE TO FIT IN THE PAD . CLAMP - RIGID "BLUE" STEEL APPROXIMATELY (4mm MINIMUM) (QTY; 3) DESCRIPTION AND MATERIAL: MAXIMUM COMPRESSION - 100 KPa = 14.5 PSI (TEMPERATURE CAPABILITY = 150`) 

S-M56-MM-03047-00-B
Patch Repair of the Abradable Shroud Figure 803 (Sheet 2)
E63101
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-33-00
 ALL  ú ú C02 Page 812 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 118-062-C00