(3)
Apply masking tape, that contains a lead adhesive, to the fan cowl panels for protection.
S 168-005-C00
(4)
Remove all the loose rust on the fan frame with a cloth. S 168-006-C00
(5)
If the rust is still there, polish the struts (radially) and the hub with an abrasive cloth.
S 168-007-C00 CAUTION: DO NOT CONTAMINATE THE BUSHINGS IN THE VARIABLE STATOR VANE OF
_______ THE COMPRESSOR FRONT STATOR WITH ENGINE OIL. IF YOU DO NOT OBEY THIS PRECAUTION, DAMAGE TO THE BUSHINGS CAN OCCUR.
(6)
Put a layer of engine oil on the clean areas with a cloth or with a brush.
S 958-008-C00
(7)
Remove the masking tape from the fan cowl panels.
S 418-009-C00 WARNING: OBEY THE INSTRUCTIONS IN THIS PROCEDURE WHEN YOU CLOSE THE
_______ THRUST REVERSER. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
(8)
Close the left or right thrust reverser (AMM 78-31-00/201). S 418-010-C00
(9)
Close the left or right fan cowl panel (AMM 71-11-02/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-33-00
ALL ú ú C02 Page 803 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
TASK 72-33-00-398-011-C00
3. ENGINES WITH THE HALLOW GLASS BEAD-LADEN EPOXY (BLUE COLOR) ABRADABLE SHROUD; Local Reconditioning of the Abradable Shroud____________________________________________
A. General
(1) This task refers to a procedure for the in-place repair of damage and grooves in the abradable shroud material.
NOTE:____Fill these areas with a base and hardener mixture. Smooth to the initial contour.
B. Equipment
(1)
Protective mats (two are necessary) - Rubber Manufacturer's Association, Grade SC43, Neoprene sponge, 1.0 inch thick, approximately 3.0 x 4.0 feet with warning streamer attached.
(2)
Scalpel - locally available
C. Consumable Materials
(1)
Abrasive cloth - CP2239 (AMM 70-10-01/201)
(2)
Acetone - CP1039 (AMM 70-10-01/201)
(3)
Base - EC 3524 or EC 3524B (AMM 70-10-01/201)
(4)
Hardener - EC 3624 or EC 3524A (AMM 70-10-01/201)
D. References
(1)
AMM 70-10-01/201, Consumable Materials
(2)
AMM 72-31-02/401, Fan Rotor Blades
E. Access
(1) Location Zones
501 Engine No. 1 - Left Inlet
601 Engine No. 2 - Right Inlet
506 Engine No. 1 - Fan Frame
606 Engine No. 2 - Fan Frame
F. Prepare to Locally Recondition the Abradable Shroud.
S 868-012-C00
(1) Make sure the start levers are in the CUTOFF position.
(a) Install the DO-NOT-OPERATE identifier on the start levers.
S 868-013-C00
(2) Open the applicable circuit breaker and install a DO-NOT-CLOSE identifier:
(a) P6 Load Control Center
1) ENG 1 START VALVE
2) ENG 2 START VALVE
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-33-00
ALL ú ú C01 Page 804 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 498-015-C00
CAUTION:_______MAKE SURE YOU INSTALL THE MATS IN THE INLET COWL. THIS WILL PREVENT DAMAGE FROM TOOLS, PARTS OR UNWANTED MATERIAL THAT FALL ON THE INLET COWL.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 ENGINE 發動機 2(29)
