F. Procedure
S 018-043-C00
(1) Open the left and right fan cowl panels (AMM 71-11-02/201).
S 018-044-C00
WARNING: OBEY THE INSTRUCTIONS IN THIS PROCEDURE WHEN YOU OPEN THE
_______
THRUST REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURY
TO PERSONS OR DAMAGE TO THE EQUIPMENT CAN OCCUR.
(2)
Open the left and right thrust reverser (AMM 78-31-00/201).
(3)
Remove the transfer gearbox (AMM 72-62-01/401).
S 018-046-C00
(4)
Do these steps to remove the radial drive shaft (RDS):
(a)
Thread the puller in the end of the radial drive shaft.
(b)
Carefully remove the radial drive shaft.
(c)
Remove the puller.
(d)
Keep the radial drive shaft in a protective tube.
S 018-045-C00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-33-00
ALL ú ú C01 Page 834 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 028-047-C00
(5) Do these steps to remove the inner and outer housings (Fig. 808):
(a) Put a container below the engine for the engine oil leakage.
WARNING: DO NOT USE CLEANING SOLVENTS NEAR OPEN FLAMES, AREAS WHERE
_______ SPARKS CAN OCCUR, OR WHERE THERE IS INADEQUATE VENTILATION. CLEANING SOLVENTS ARE FLAMMABLE, VOLATILE, AND POISONOUS.
(b)
Remove the grease or oil with acetone where you removed the transfer gearbox.
(c)
Remove the 4 bolts that hold the outer housing to the fan frame.
(d)
Install the guide puller in the inner and outer housings.
(e)
Carefully remove the inner and outer housings.
(f)
Remove the guide puller from the inner and outer housings.
S 428-048-C00
(6) Do these steps to install the new inner and outer housings:
(a)
Clean all the engine oil from the inner surface of the bore diameter (fan frame strut number 10) with a lint-free cloth that is wet with acetone.
(b)
Clean all the grease from the new inner and outer housings with a lint-free cloth that is wet with acetone.
(c)
Put a light layer of engine oil on the two new O-rings for the outer housing.
(d)
Install the O-rings on the external grooves of the large diameter of the outer housing.
(e)
Install the outer housing on the guide puller.
(f)
Put a light layer of engine oil on the new O-ring for the inner housing.
(g)
Install the O-ring in the external groove of the small diameter of the inner housing.
(h)
Install the inner housing on the guide puller and on the diameter of the outer housing.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-33-00
ALL ú ú C01 Page 835 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
FAN FRAME
STRUT
A
A
INNER RADIAL
DRIVE SHAFT
HOUSING
O-RING
BORE DIAMETER
SHOULDER OF
FAN FRAME
BORE DIAMETER
OF FAN FRAME
O-RINGS
OUTER RADIAL
DRIVE SHAFT
HOUSING
FWD
TGB/FAN FRAME INTERFACE
(WITHOUT TOOL INSTALLED) A-A
S-M56-MM-00537-00-B
Inner and Outer Radial Drive Shaft Housing Figure 808 (Sheet 1)
C85989
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 ENGINE 發動機 2(42)
