Bleed Valve Door Position Check
Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ENGINES WITHOUT CFMI SB 72-580 ú
75-32-03
ú ú C02 Page 408 ú Nov 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
A
SEE A
A
FWD
A
1/8 TURN
SLIDE 45` SLIDE
ì ì
FAIRING FAIRING
VBV DOOR
TOUCHES
THE SCOOP SCOOP SCOOP
INITIAL RIGGING 1/8 TURN ADJUSTMENT
A-A A-A
VBV Door Rigging
Figure 403
B11003
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ENGINES WITH CFMI SB 72-580 ú
75-32-03
ú ú C02 Page 409 ú Nov 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 434-046-C00
(15) Install and engage the flexible shafts on each side of the master ballscrew actuator.
NOTE: To do this, put in position and compress the spring hexagonal
____
end of the flexible shaft at the positions that follow:
-
the end away from the actuator (upper shaft)
-
the actuator end (lower shaft).
Do this while you engage the 8-point fitting at the opposite
end.
Look for the best position of the splined ends of the VBV flexible shaft. Do not move an adjusted door to install the flexible shaft into the next door.
S 434-047-C00
(16)
Engage the main flexible shaft.
S 434-048-C00
(17)
Connect the VBV feedback rod on the feedback lever for door position as follows:
(a) Lubricate the exposed sides of the uniballs, with three to four drops of water repellant (CP2857). 1) Let the lubricant soak for 2-3 minutes. 2) Manually turn the uniballs in all directions.
NOTE: If binding or frozen slightly, use an open-end
____ wrench on the linkage to turn the rod end.
3) Apply three to four more drops of lubricant if it is necessary. 4) Move the uniballs in all directions until movement is smooth and free. 5) Wipe off the excess lubricant.
(b)
Put the clevis in position on the feedback lever.
(c)
Lubricate the bolt threads with grease.
(d)
Install the bolt, washer and slotted nut.
(e)
Tighten the slotted nut, while you align the nut slot with the cotter pin hole.
NOTE: Replace the nut if:
____
-
you cannot get the minimum torque value
-
you get more than the maximum torque value.
(f) Install and bend the cotter pin on the two sides of the nut.
S 824-049-C00
(18) ON ENGINES WITH CFMI SB 72-580; do the VBV kicker adjustment (AMM 75-32-02/501).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-32-03
ALL ú ú C01 Page 410 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 414-050-C00
(19)
Install the fan duct panel(s) (AMM 72-33-03/401).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 空氣 AIR(103)
