-
the centerline of the cable attachment hole of the MEC
feedback arm.
1) If there is no overlap, make the cable longer.
NOTE: To do this, loosen the jamnut and turn the rod end
____
bearing.
(j) Do a check that the threads are sufficiently engaged.
NOTE: To do this, make sure a 0.032 inch (0.80 mm) diameter
____ lockwire does not go through the witness hole.
1) If the threads are not correctly engaged, adjust the length. Do the steps to check the cable length at the MEC end.
NOTE: To do this, turn the rod end bearing.
____
(k)
If you adjusted the rod end bearing, tighten the jamnut against the rod end bearing to 24-27 pound-inches (2.7-3.1 Newton meters).
(l)
Attach the rod end bearing to the MEC feedback arm.
1) ON ROD-END BEARINGS WITH DROP-IN UNIBALLS (WITH CFMI SB 72-667), lubricate the uniballs on the rod end bearing. a) Lubricate the two sides of the uniballs on the rod end
bearing with LPS-1 penetrating oil.
1. Let the uniballs soak in the oil for 2-3 minutes.
_
b) Turn the uniballs back and forth in the two directions fully three times, until there is a smooth operation of the uniballs.
1. If more oil is necessary for smooth operation, do
_ the above steps again. c) Wipe off all unwanted oil with a lint free cloth.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-31-02
ALL ú ú C01 Page 513 ú Mar 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
d) Put the rod end bearing in position on the inboard side of the lever arm.
2) ON ROD-END BEARINGS WITH UNIBALLS STAKED IN WITH TEFLON SLEEVES (WITHOUT CFMI SB 72-667), put the rod end bearing on the inboard side of the feedback arm.
3) Install the washer and bolt (the bolt head must point to
the fan case).
4) Install the slotted nut.
5) Tighten the nut to 20-40 pound-inches
(2.3-4.5 Newton meters) while you align the nut slot with the cotter pin hole.
NOTE: Replace the nut if you cannot get the minimum torque
____ value, or if you go above the maximum torque value.
6) Install the cotter pin.
7) Bend the ends of the pin around the nut flats.
H. AIRCRAFT WITH MEC P/N 9368M57P11; Initial Static Rig Check (Fig. 504)
S 725-012-C00
CAUTION: ON CFM56-3-B1 ENGINES WITH P/N 9368M57P11 MEC, THIS STATIC RIG
_______
PROCEDURE MUST BE DONE. DO IT AFTER THE INITIAL INSTALLATION
OF A P/N 9368M57P11 MEC. THIS IS TO CLOSE THE VSV SCHEDULE BY
ONE DEGREE AND MAKE SURE OF THE CORRECT CABLE RIG. WHEN A
CHECK IS DONE OF THE VSV STATIC RIG, THE RIG POINTER MUST BE
ADJUSTED TO THE NOTCH OF THE VARIABLE RIG PLATE, REFER TO THE
INITIAL STATIC RIG CHECK.
(1)
Do a check that the notch on the variable rig plate is aligned with
the notch on the MEC casting.
S 825-013-C00
(2)
If the notch of the variable rig plate and the MEC casting notch are not aligned, do the steps that follow:
(a)
Loosen the two screws on the variable rig plate.
(b)
Turn the variable rig plate to align the rig plate notch and the MEC casting notch.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-31-02
ALL ú ú C01 Page 514 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(c) Tighten the two screws to 7-9 pound-inches (0.8-1.0 Newton meters).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空氣 AIR(68)
