34-22-01
ALL ú ú 03 Page 303 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
STANDBY COMPASS - REMOVAL/INSTALLATION
______________________________________
1. General
_______
A. This procedure contains two tasks. The first task is for the removal of the standby compass. The second task is for the installation of the standby compass.
B. The standby compass (N100) is installed on the forward overhead panel (P43).
TASK 34-22-01-004-001
2. Remove The Standby Compass (Fig. 401)
_____________________________________
A. Standard Tools and Equipment
(1) Screwdriver - nonmagnetic
B. References
(1) IPC 34-22-01 Fig. 1
C. Access
(1) Location Zones
221 Control Cabin, LH
D. Procedure
S 864-002
(1) Open these circuit breakers and attach the DO-NOT-CLOSE tags:
(a) P6 Main Power Distribution Panel 1) 6E21 FLT DK LIGHTS PANEL GLARE SHIELD 2) 6L1 FLT DECK LIGHT STBY INST
S 424-014
CAUTION: USE ONLY TOOLS THAT ARE NOT MAGNETIC FOR THE REMOVAL AND THE
_______ INSTALLATION OF THE STANDBY COMPASS. MAGNETIC TOOLS CAN CAUSE INSTRUMENT DAMAGE.
(2) Do these steps to remove the standby compass:
(a)
Disconnect the DN100 electrical connector from the rear of the standby compass.
(b)
Hold the compass and remove the brass screws.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-22-01
ALL ú ú 01 Page 401 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
FLIGHT COMPARTMENT
PANEL
A
Standby Compass Location Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-22-01
ALL ú ú 01 Page 402 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
TASK 34-22-01-404-004
3. Install The Standby Compass (Fig. 401)
______________________________________
A. Standard Tools and Equipment
(1) Screwdriver - nonmagnetic
B. Reference
(1)
24-22-00/201, Manual Control
(2)
34-22-00/201, Standby Magnetic Compass
(3)
IPC 34-22-01 Fig.1
C. Access
(1) Location Zones
221 Control Cabin, LH
D. Procedure
S 864-005
(1) Make sure these circuit breakers are open with the DO-NOT-CLOSE tags attached:
(a) P6 Main Power Distribution Panel 1) 6E21 FLT DK LIGHTS PANEL GLARE SHIELD 2) 6L1 FLT DECK LIGHT STBY INST
S 424-006
CAUTION: USE ONLY TOOLS THAT ARE NOT MAGNETIC FOR THE REMOVAL AND THE
_______ INSTALLATION OF THE STANDBY COMPASS. MAGNETIC TOOLS CAN CAUSE INSTRUMENT DAMAGE.
CAUTION: DO NOT USE STEEL SCREWS TO ATTACH THE COMPASS TO THE PANEL.
_______ STEEL SCREWS CAN CAUSE COMPASS INDICATIONS THAT ARE IN ERROR.
(2) Do these steps to install the standby compass:
(a) Align the standby compass with the holes in the P43 panel.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-22-01
ALL ú ú 01 Page 403 ú Jun 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(b) (c) Install the brass screws to attach the standby compass to the P43 panel.Connect the DN100 electrical connector to the rear of the standby compass.
(3) S 864-008Remove the DO-NOT-CLOSE tags and close these circuit breakers: (a) P6 Main Power Distribution Panel 1) 6E21 FLT DK LIGHTS PANEL GLARE SHIELD 2) 6L1 FLT DECK LIGHT STBY INST
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 導航 NAVIGATION 2(10)
