34-43-04
ALL ú ú 04B Page 404 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 024-038
(3) Remove waveguide Section 3:
(a)
Remove four screws and lockwashers from flanges between section 2 and section 3.
(b)
Remove four screws and lockwashers from flanges between section 3 and section 4.
(c)
Remove waveguide section 3 and gaskets.
S 024-132
(4) Put dust caps on the waveguide flanges.
F. Waveguide Section 4 Removal
NOTE: To remove waveguide Section 4, it is necessary to get into the
____ nose radome and below the compartment floor in the nose cargo door.
S 864-040
(1) Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a) P7 Overhead Circuit Breaker Panel
1) 7C7 WXR L RT
2) 7C19 WXR R RT
S 014-239
(2) Get access to section 4 below the compartment floor:
(a) Release the 18 fasteners that hold the cargo floor panel.
WARNING: STEP ONLY ON THE FLOOR BEAMS WHEN YOU REMOVE CARGO FLOOR
_______ PANEL. THE FLOOR PANELS BETWEEN THE BEAMS CAN FLEX AND CAUSE YOU TO FALL. IF YOU DO NOT OBEY THESE INSTRUCTIONS, INJURY TO PERSONNEL AND/OR DAMAGE TO THE WEATHER RADAR EQUIPMENT OR BLANKET MATERIAL CAN OCCUR.
WARNING:_______THE CARGO FLOOR PANEL IS HEAVY. TO PREVENT INJURY, TWO PEOPLE ARE REQUIRED WHEN LIFTING OR MOVING THE CARGO FLOOR PANEL.
CAUTION: DO NOT PUSH OR PULL THE CARGO FLOOR PANEL ACROSS THE FLOOR
_______ BEAMS. THIS ACTION CAN CAUSE DAMAGE TO THE BLANKET MATERIAL.
(b) Carefully remove the cargo floor panel.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-43-04
ALL ú ú 03B Page 405 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 024-042
(3) Remove waveguide section 4:
(a)
Remove four screws and lockwashers from flanges between section 3 and section 4.
(b)
Remove four screws and lockwashers from section 4 flange that mates with the waveguide switch.
NOTE: The screws go through the holes in the waveguide switch
____
support bracket into the waveguide switch.
(c) Remove waveguide section 4. 1) Hold the waveguide switch away from the waveguide switch support. 2) Slide the Section 4 through the slot in the bottom of the
waveguide switch support. 3) Remove waveguide section 4 and gaskets.
S 024-119
(4) Put dust caps on the waveguide flanges.
G. R/T Feeder Waveguide Section Removal
NOTE: To remove one or both R/T feeder waveguide sections,
____ it is necessary to get below the compartment floor in the nose cargo door.
S 864-044
(1) Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a) P7 Overhead Circuit Breaker Panel
1) 7C7 WXR L RT
2) 7C19 WXR R RT
S 014-240
(2) Get access to L/T feeder waveguide section below the compartment floor:
(a) Release the fasteners that hold the cargo floor panel.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-43-04
ALL ú ú 02B Page 406 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
WARNING: STEP ONLY ON THE FLOOR BEAMS WHEN YOU REMOVE CARGO FLOOR 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 導航 NAVIGATION 2(137)
