(e)  
Attach a master magnetic compass to the SCC with two mounting screws.

 NOTE: You can use an accurate standby magnetic compass for a
____ master magnetic compass. Make sure that the N-S and E-W adjustment screws are at neutral.
 (f)  Put the SCC/master compass assembly on the tripod.
 NOTE: Make sure the assembly is level.
____
 (g)  
Turn the assembly until the master magnetic compass shows an indication of magnetic north (N).

 (h)  
Install the magnet assembly onto the SCC/master compass assembly.

 (i)  
Turn the top and bottom SCC dials to show an indication of E at the index line.

 (j)  
Make a record of the heading shown on the master magnetic compass.

 (k)  
Turn the top and bottom SCC dials to show an indication of W at the index line.

 (l)  
Make a record of the heading shown on the master magnetic compass.

 (m)  
Turn the magnetic field cancellation adjustment screw on the SCC to decrease the heading errors in each direction (E and W) to a minimum.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-22-00
 ALL  ú ú 03 Page 206 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

MAGNETIC FIELD CANCELLATION ADJUSTMENT SCREW
Standby Compass Calibrator
Figure 201

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-22-00
 ALL  ú ú 01 Page 207 ú Feb 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E77126
A
747-400
MAINTENANCE MANUAL

 (n)  Continue to adjust the SCC dials for each direction (E and W). Then use the field cancellation adjustment screw until the errors are at a minimum.
 NOTE: Continue to do this procedure until the error in each
____
 direction is at a minimum.

 Do not move the field cancellation adjustment screw
 before the compass swing is completed.
 E. Prepare for a Compass Swing of the Standby Compass
 NOTE: Ferromagnetic parts installed near the standby compass can cause
____ compass heading errors. Make sure no ferromagnetic parts are near the captain's and the first officer's window frames. If found, replace the parts with non-magnetic, corrosion-resistant steel (CRES) parts.
 S 582-062
 (1)  Tow the airplane to the compass swing area (AMM 9-11-00/201).
 NOTE: The compass swing area must be a level area with a smooth
____ surface. It must be sufficiently strong to hold the weight of the airplane. The area must be large enough to tow or taxi the airplane. Make sure all vehicles other than the tow vehicle are not less than 250 feet from the airplane.
 The horizontal component of the earth's magnetic field must be constant (|1 degree) in the test area. Measure the horizontal component if magnetic material (such as a new building) is less than 600 feet from the compass rose. Do not use the compass rose if the horizontal component is not constant (|1 degree).
 S 862-063
 (2)  
Supply the electrical power (AMM 24-22-00/201).

 S 862-071

 (3)  
Energize all of the electronic equipment, radios, and control cabin lighting for the usual conditions that occur in flight.

 S 862-064

 (4)  
Set the mode selector on the EFIS control panels to VOR
 (AMM 31-61-00/501).

 (5)  
Set the HDG switch above the upper EICAS display to MAG.

 S 862-066
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-22-00
 ALL  ú ú 02 Page 208 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 862-067
 (6)  Align the IRS to the NAV mode (AMM 34-21-00/201).
 S 862-068
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 導航 NAVIGATION 2(7)