曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(1)  Make a copy of the Control Surfaces Adjustment Report.  Refer to Section 06-00. Use it to record the measurements. 
(2)  Make sure that the flaps are fully UP: S Set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to ON. S Set the flaps to T/O. S When the flaps stop moving, set the flaps to UP. S When the flaps stop moving, set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to OFF. 
(3)  Do a test for the correct pre-load in the flap UP position: S Put a loop of adhesive tape on the trailing edge of the left flap opposite the up-stop. S Pull down on the loop of tape with the spring balance until the flap just moves from the up-stop. S Record the value in the Control Surfaces Adjustment Report.  The value must be as shown in the Control Surfaces Adjustment Report. 
(4)  If the pre-load is not correct, adjust the control rod between the bellcrank in the wing and the flap horn. Do items 3 & 4 again as necessary.  Refer to Section 27-00. 

Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003

27-50-00
AMM

%
%
%

%
%

%
%
%

%
%

DA 40 Series

Detail Steps/Work Items  Key Items/References 
(5)  Do items 3 & 4 for the right flap. 
(6)  Zero the inclinometer to the left flap: S Put the inclinometer on the left flap close to the flap horn. S Zero the inclinometer. S Remove the inclinometer. 
(7)  Set the flaps to T/O: S Set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to ON. S Set the flaps to T/O. S When the flaps stop moving, set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to OFF. 
(8)  Measure the angle of the left flap. S Record the value in the Control Surfaces Adjustment Report.  Use the inclinometer. The value must be as shown in the Control Surfaces Adjustment Report. 
(9)  Do item 8 for the right flap. 
(10)  Set the flaps to LDG: S Set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to ON. S Set the flaps to LDG. S When the flaps stop moving, set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to OFF. 
(11)  Measure the angle of the left flap. S Record the value in the Control Surfaces Adjustment Report.  Use the inclinometer. The value must be as shown in the Control Surfaces Adjustment Report. 
(12)  Do item 11 for the right flap. 
(13)  Set the flaps to UP. 

Page 204 Doc # 6.02.01 09 Jan 2003 Rev. 4
27-50-00
Flight Controls
AMM

4. Adjust the Flap Control System
If you cannot get the correct range of movement of the flap control system, use this procedure to adjust the system.
A. Equipment
Item  Quantity  Part Number 
Rigging pins.  3  -
Inclinometer.  1  Commercial. 

B. Adjust The Flap Control System Procedure
%
%

%
%

Detail Steps/Work Items  Key Items/References 
(1)  Make a copy of the Control Surfaces Adjustment Report.  Refer to Section 06-00. Use it to record the measurements. 
(2)  Remove these items for access: S The passenger seat. S The flap bellcrank access panels.  Refer to Section 25-10. Refer to Section 53-40. 
(3)  Disconnect the airplane main battery.  Refer to Section 24-31 (Lycoming version) or 24-34 (TAE version). 
(4)  Remove the bolt, spacer, washer and nut which attach the actuator push-rod to the idler lever.  At the rear main bulkhead. Hold the flaps. 
(5)  Put a rigging pin in the idler lever.  Refer to Figure 3. At the rear main bulkhead. 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 3(24)